BS EN 62752:2016

BS EN 62752:2016 applies to in-cable control and protection devices (IC-CPDs) for mode 2 charging of electric road vehicles, hereafter referred to as IC-CPD including control and safety functions.

This standard applies to portable devices performing simultaneously the functions of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value.

The IC-CPD according to this standard

• has a control pilot function controller in accordance with IEC TS 62763;
• checks supply conditions and prevents charging in case of supply faults under specified conditions;
• may have a switched protective conductor.

These IC-CPDs are intended for use in TN-, and TT-systems.

The use of IC-CPDs in IT systems may be limited.

Residual currents with frequencies different from the rated frequency, d.c. residual currents and specific environmental situation are considered.

This standard is applicable to IC-CPDs performing the safety and control functions as required in IEC 61851-1 for mode 2 charging of electric vehicles.

This standard is applicable to IC-CPDs for single-phase circuits not exceeding 250 V or multiphase circuits not exceeding 480 V, their maximum rated current being 32 A.

NOTE 1 In Denmark, the following additional requirement applies: for IC-CPDs supplied with a plug for household and similar use the maximum charging current is 8 A, if the charging cycle can exceed 2 h.

NOTE 2 In Finland, the following additional requirement applies: for IC-CPDs supplied with a plug for household and similar use the maximum charging current is 8 A for long lasting charging.

This standard is applicable to IC-CPDs to be used in a.c. circuits only, with preferred values of rated frequency 50 Hz, 60 Hz or 50/60 Hz. IC-CPDs according to this standard are not intended to be used to supply electric energy towards the connected grid.

This standard is applicable to IC-CPDs having a rated residual operating current not exceeding 30 mA and are intended to provide additional protection for the circuit downstream of the IC-CPD in situations where it cannot be guaranteed that the installation is equipped with an RCD with IΔn ≤ 30 mA.


Cross References:
IEC 60065
IEC 60068-2-1
IEC 60068-2-5
IEC 60068-2-11
IEC 60068-2-27
IEC 60068-2-30
IEC 60068-2-31
IEC 60068-2-64
IEC 60068-3-4
IEC 60112
IEC 60227
IEC 60245
IEC 60309
EN 60065
EN 60068-2-1
EN 60068-2-5
EN 60068-2-11
EN 60068-2-27
EN 60068-2-31
EN 60068-2-64
EN 60068-3-4
EN 60112
EN 60309
IEC 60309-1:1999
IEC 60309-1:1999/A1:2005
IEC 60309-1:1999/A2:2012
IEC 60309-2
IEC 60364-4-44:2007
IEC 60384-14
IEC 60417-DB
IEC 60529:1989
IEC 60664-1:2007
IEC 60664-3
IEC 60695-2-10
IEC 60695-2-11
IEC 60884-1:2002
IEC 60884-1:2002/A1:2006
IEC 60884-1:2002/A2:2013
IEC 61540
EN 60309-1:1999
EN 60309-1:1999/A11:2004
EN 60309-1:1999/A1:2007
EN 60309-1:1999/A2:2012
EN 60309-2
HD 60364-4-442:2012
EN 60384-14
EN 60529:1991
EN 60664-1:2007
EN 60664-3
EN 60695-2-10
EN 60695-2-11
EN 61249-2
HD 639 S1
IEC 61543:1995
IEC 61543:1995/A1:2004
IEC 61543:1995/A2:2005
IEC 61851-1:2010
IEC 62196-1
IEC 62196-2
IEC/TS 62763:2013
CISPR 14
ISO 178
ISO 179
ISO 179-1
ISO 2409
ISO 4628-3
ISO 4892-2:2013
ISO 16750-5:2010
ISO 17409:2015
EN 61543:1995
EN 61543:1995/A11:2003
EN 61543:1995/A12:2005
EN 61543:1995/A2:2006
EN 61851-1:2011
EN 62196-1
EN 62196-2
EN 55014
EN ISO 178
EN ISO 179
EN ISO 179-1
EN ISO 2409
EN ISO 4628-3
EN ISO 4892-2:2013
2014/35/EU
2014/30/EU
IEC 60050-441:1984
IEC 60050-604:1987
IEC 60050-604:1987/AMD 1:1998
IEC 60269-1:2006
IEC 60364
IEC 60364-7-722
IEC TR 60755:2008
IEC 60999-1:1999
IEC 60947-1:2007
IEC 60479
IEC 61008-1:2010
IEC 62335:2008
IEC 62423:2009
IEC Guide 117
ISO 16750-3:2012
ISO 16750-4:2010
ASTM D785-08


Replaces BS EN 61851-1:2011 which remains current.

All current amendments available at time of purchase are included with the purchase of this document.