Language:
    • Available Formats
    • Options
    • Availability
    • Priced From ( in USD )
    • Printed Edition
    • Ships in 1-2 business days
    • $48.00
    • Add to Cart
    • Printed Edition + PDF
    • Immediate download
    • $65.00
    • Add to Cart

Customers Who Bought This Also Bought

 

About This Item

 

Full Description

1.1 These test methods cover three electrical tests on plastic guards and assembled guard systems. They are:

1.1.1 Method A-Withstand voltage proof test,

1.1.2 Method B-Flashover voltage, and

1.1.3 Method C-Leakage current.

1.1.4 This specification covers plastic guard equipment and guard systems used by workers for temporary insulation on electric power circuits.

1.1.5 Plastic guard equipment covered by this specification is rated for momentary, or brush contact only. Maximum-use voltages are covered in Table 1 and Table 2.

(A) Cover-up materials are tested at values greater than the maximum use phase to ground values. The maximum use phase to phase values relate to guarded phase to guarded phase. The units are not rated for bare phase to guarded phase potentials.
(A) Cover-up materials are tested at values greater than the maximum use phase to ground values. The maximum use phase to phase values relate to guarded phase to guarded phase. The units are not rated for bare phase to guarded phase potentials.

1.2 These test methods cover, but are not limited to, the following typical guards:

1.2.1 Conductor Guards and Connecting Covers as follows: 

1.2.1.1 Line guards,

1.2.1.2 Line guard connectors,

1.2.1.3 Insulator covers,

1.2.1.4 Dead-end covers,

1.2.1.5 Bus guards, and

1.2.1.6 Bus “T” guards.

1.2.2 Structure and Apparatus Covers as follows: 

1.2.2.1 Pole guards,

1.2.2.2 Ridge pin covers,

1.2.2.3 Switch blade covers,

1.2.2.4 Arm guards,

1.2.2.5 Cutout covers,

1.2.2.6 Structural barriers, and

1.2.2.7 Cross arm guard.

1.3 It is common practice for the user of this equipment to prepare instructions for the correct use and maintenance.

1.4 The use and maintenance of this equipment is beyond the scope of these test methods.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

 

Document History

  1. ASTM F712-06(2018)

    👀currently
    viewing


    Standard Test Methods and Specifications for Electrically Insulating Plastic Guard Equipment for Protection of Workers

    • Most Recent
  2. ASTM F712-06(2011)


    Standard Test Methods and Specifications for Electrically Insulating Plastic Guard Equipment for Protection of Workers

    • Historical Version
  3. ASTM F712-06


    Standard Test Methods and Specifications for Electrically Insulating Plastic Guard Equipment for Protection of Workers

    • Historical Version
  4. ASTM F712-88(2000)


    Standard Test Methods for Electrically Insulating Plastic Guard Equipment for Protection of Workers

    • Historical Version
  5. ASTM F712-88(1995)


    Standard Test Methods for Electrically Insulating Plastic Guard Equipment for Protection of Workers

    • Historical Version