Latest Standards From Techstreet

ASTM F593-13 : Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This specification covers the requirements for stainless steel bolts, hex cap screws, and studs 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.

1.2 Seven groups of stainless steel alloys are covered, including twelve austenitic, two ferritic, four martensitic, and one precipitation hardening.

Group	Alloys^A	Condition^B
1	304, 305, 384, 304 L,	(CW) cold worked^C
	18-9LW, 302HQ^D
2	316, 316 L	(CW) cold worked^C
3	321, 347	(CW) cold worked^C
4	430^E	(CW) cold worked^C
5	410^F	(H) hardened and tempered
6	431	(H) hardened and tempered
7	630	(AH) age hardened

^A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer (see 6.1).

^B See 4.2 for options.

^C Sizes 0.75 in. and larger may be hot worked and solution annealed, provided the bolts comply with the cold worked (CW) mechanical property requirements.

^D When approved by the purchaser, Alloys 303, 303Se, or XM1 may be furnished.

^E When approved by the purchaser, Alloy 430F may be furnished.

^F When approved by the purchaser, Alloys 416 or 416Se may be furnished.

1.3 Supplementary requirements of an optional nature are provided, applicable only when agreed upon between the manufacturer and the purchaser at the time of the inquiry and order.

1.4 Suitable nuts for use with bolts, hex cap screws, and studs included in this specification are covered by Specification F594. Unless otherwise specified, all nuts used on these fasteners shall conform to the requirements of Specification F594, shall be of the same alloy group, and shall have a specified minimum proof stress equal to or greater than the specified minimum full-size tensile strength of the externally threaded fastener.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F450-13 : Standard Test Methods for Vacuum Cleaner Hose—Durability and Reliability (Plastic)

Wed, 19 Jun 2013 13:30:39 -0500

1.1 These test methods cover the determination of the effect of anticipated stresses and strains that vacuum cleaner and extractor hoses will receive in normal use.

1.2 These test methods apply to plastic (regular and reinforced) vacuum cleaner and extractor hoses for household use.

1.3 The following tests are included:

	Section
Torsional flex	6
Hot and cold flex with aging	7
Abrasion, external surfaces	8
Flex	9
Pull test on hose fittings with aging	10
Crush	11
Stretch ratio	12
Extractor hoses	13

1.4 These test methods are individual tests as agreed upon between the hose and vacuum manufacturer.

ASTM F2970-13 : Standard Practice for Design, Manufacture, Installation, Operation, Maintenance, Inspection and Major Modification of Trampoline Courts

Wed, 19 Jun 2013 13:30:39 -0500

1.1 The purpose of this practice is to delineate requirements regarding the design, manufacture, installation, operation, maintenance, inspection and major modification of commercial or institutional trampoline courts with the primary purpose of amusement, entertainment or recreation.

1.2 This standard applies to institutional trampoline courts that are located in and around amusement, entertainment or recreational facilities. Such facilities include but are not limited to trampoline parks, amusement parks, theme parks, water parks, family entertainment centers, fitness centers, gyms, gymnastics facilities, sports facilities, skate parks, camps, shopping centers, temporary special events, carnivals and municipal parks.

1.3 This practice establishes guidelines that will provide a level of conformity for the purpose of reducing potential hazards to patrons, court attendants, and spectators.

1.4 This standard does not purport to address all of the hazards associated with institutional trampoline courts. The standard's existence alone will not prevent injuries. Like other physical activities, institutional trampoline court use involves the risk of injury, particularly if the equipment is used improperly or if users exceed their capabilities, endurance, training, or experience.

1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

1.6 This practice includes an annex (mandatory), which provides additional information (for example, rationale, background, interpretations, drawings, commentary, and so forth) to improve the user's understanding and application of the criteria presented in this practice. The annex information shall be interpreted as mandatory criteria.

1.7 This practice includes an appendix (non-mandatory), which provides additional information (for example, rationale, background, interpretations, drawings, commentary, and so forth.) to improve the user's understanding and application of the criteria presented in this practice. The appendix information shall not be interpreted as mandatory criteria.

1.8 This practice shall apply to trampoline courts manufactured after the date this standard practice is published.

1.9 This standard includes the following sections:

	Section
Scope	1
Referenced Documents	2
Terminology	3
Significance and Use	4
Quality, Manufacture, Construction and Installation	5
General Design	6
Design	7
Major Modification	8
Information Plate	9
Information Requirements	10
Certifications	11
Performance Criteria	12
Classification of Injuries and Illnesses	13
Notification Requirements	14
Manufacturer Responsibilities	15
Owner/Operator Responsibilities	16
Patron Education	17
Patron Responsibility	18
Keywords	19
Annex	Annex A1
Appendix	Appendix X1

1.10 Units-The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.11 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F2613-13 : Standard Consumer Safety Specification for Children's Chairs and Stools

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This consumer safety specification establishes testing requirements for structural integrity and performance requirements for children's chairs and stools. It also provides requirements for labeling. The standard does not apply to products used in a commercial setting. The term unit or product will refer to a child's chair or stool.

1.2 This specification covers a chair or stool intended to be used by a child with a seat height 15 in. or less.

1.3 No product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and after all testing.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F2576-13 : Standard Terminology Relating to Declarable Substances in Materials

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This terminology standard contains terms, definitions, descriptions of terms, nomenclature, and explanations of acronyms and symbols specifically associated with standards under the jurisdiction of ASTM International Committee F40 on Declarable Substances in Materials.

1.2 This terminology may also be applicable to documents not under the jurisdiction of ASTM F40, in which case this terminology may be referenced in those documents.

ASTM F2506-10e1 : Standard Specification for Design and Testing of Fixed-Pitch or Ground Adjustable Light Sport Aircraft Propellers

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This specification covers the establishment of the minimum requirements for the design, testing, and quality assurance of fixed-pitch or ground adjustable propellers for light sport aircraft. These propellers are used on light aircraft, and could be used with engines conforming to Practice F2339.

1.2 This specification is intended for use by manufacturers of propellers for light sport aircraft.

1.3 This specification does not address the airframe installation requirements for propellers.

ASTM F2471-13 : Standard Practice for Installation of Thick Poured Lightweight Cellular Concrete Underlayments and Preparation of the Surface to Receive Resilient Flooring

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This practice covers the installation and preparation of the thick poured lightweight cellular concrete underlayments over wood structural panel subfloors in commercial structures or over concrete floors in commercial structures and the preparation of the thick poured lightweight cellular concrete underlayment surface prior to the installation of resilient flooring in commercial buildings.

1.2 This practice points out the factors that are required to be controlled while installing thick poured lightweight cellular concrete underlayment as a base for resilient flooring.

1.3 This practice does not cover the structural adequacy of the wood structural panel subfloor or concrete subfloor. The structural integrity of assemblies is governed by local building codes.

1.4 This practice does not supercede the thick poured lightweight cellular concrete underlayment manufacturers', adhesive manufacturers' or resilient flooring manufacturers' written instructions. Consult the individual manufacturer for specific recommendations.

1.5 Thick poured lightweight cellular concrete underlayments are not suitable for use on concrete slabs on ground due to potential moisture problems arising from moisture intrusion, unless an adequate vapor retarder or vapor barrier is present directly beneath the concrete subfloor.

1.6 The values stated in inch-pound units are to be regarded as standard. The values stated in parentheses are mathematical conversions to SI Units, which are provided for information only.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F2245-13a : Standard Specification for Design and Performance of a Light Sport Airplane

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This specification covers airworthiness requirements for the design of powered fixed wing light sport aircraft, an “airplane.”

1.2 This specification is applicable to the design of a light sport aircraft/airplane as defined by regulations and limited to VFR flight.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

ASTM F1671/F1671M-13 : Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Blood-Borne Pathogens Using Phi-X174 Bacteriophage Penetration as a Test System

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This test method is used to measure the resistance of materials used in protective clothing to penetration by blood-borne pathogens using a surrogate microbe under conditions of continuous liquid contact. Protective clothing material pass/fail determinations are based on the detection of viral penetration.

1.1.1 This test method is not always effective in testing protective clothing materials having thick, inner liners which readily absorb the liquid assay fluid.

1.2 This test method does not apply to all forms or conditions of blood-borne pathogen exposure. Users of the test method should review modes for worker/clothing exposure and assess the appropriateness of this test method for their specific applications.

1.3 This test method has been specifically defined for modeling the viral penetration of Hepatitis (B and C) and Human Immunodeficiency Viruses transmitted in blood and other potentially infectious body fluids. Inferences for protection from other pathogens must be assessed on a case-by-case basis.

1.4 This test method addresses only the performance of materials or certain material constructions (for example, seams) used in protective clothing and determined to be viral resistant. This test method does not address the design, overall construction and components, or interfaces of garments or other factors which may affect the overall protection offered by the protective clothing.

1.5 The values stated in SI units or in other units shall be regarded separately as standard. The values stated in each system must be used independently of the other, without combining values in any way.

ASTM F1649-13 : Standard Test Methods for Evaluating Wet Braking Traction Performance of Passenger Car Tires on Vehicles Equipped with Anti-Lock Braking Systems

Wed, 19 Jun 2013 13:30:39 -0500

1.1 These test methods cover the measurement of two types of ABS vehicle behavior that reflect differences in tire wet traction performance when the vehicle is fitted with a series of different tire sets to be evaluated.

1.1.1 The stopping distance from some selected speed at which the brakes are applied.

1.1.2 The lack of control of the vehicle during the braking maneuver. Uncontrollability occurs when the vehicle does not follow the intended trajectory during the period of brake application despite a conscious effort on the part of a skilled driver to maintain trajectory control. Uncontrollability is measured by a series of parameters related to this deviation from the intended trajectory and the motions that the vehicle makes during the stopping maneuver.

1.1.3 Although anti-lock braking systems maintain wheel rotation and allow for a high degree of trajectory control, different sets of tires with variations in construction, tread pattern, and tread compound may influence the degree of trajectory control in addition to stopping distance. Thus vehicle uncontrollability is an important evaluation parameter for tire wet traction performance.

1.2 These test methods specify that the wet braking traction tests be conducted on two specially prepared test courses: (1) a straight-line (rectilinear) “split-µ” (µ = friction coefficient) test course, with two test lanes deployed along the test course (as traveled by the test vehicle); the two lanes have substantially different friction levels such that the left pair of wheels travels on one surface while the right pair of wheels travels on the other surface; and (2) a curved trajectory constant path radius course with uniform pavement for both wheel lanes.

1.3 As with all traction testing where vehicle uncontrollability is a likely outcome, sufficient precautions shall be taken to protect the driver, the vehicle, and the test site facilities from damage due to vehicle traction breakaway during testing. Standard precautions are roll-bars, secure mounting of all internal instrumentation, driver helmet, and secure seat belt harness, etc.

ASTM E662-13a : Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This fire-test-response standard covers determination of the specific optical density of smoke generated by solid materials and assemblies mounted in the vertical position in thicknesses up to and including 1 in. (25.4 mm).

1.2 Measurement is made of the attenuation of a light beam by smoke (suspended solid or liquid particles) accumulating within a closed chamber due to nonflaming pyrolytic decomposition and flaming combustion.

1.3 Results are expressed in terms of specific optical density which is derived from a geometrical factor and the measured optical density, a measurement characteristic of the concentration of smoke.

1.4 This test method is intended for use in research and development and not as a basis for ratings for regulatory purposes.

1.6 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.

ASTM E618-07(2013) : Standard Test Method for Evaluating Machining Performance of Ferrous Metals Using an Automatic Screw/Bar Machine

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This test method covers a production-type test for evaluating the machining performance of ferrous metals as they are used in single-spindle or multiple-spindle automatic screw machines. It is based on producing parts of a standard design in such machines to uniform levels of quality with respect to surface roughness and size variation. The standard test piece, designed for this test, is machined from bars using a specified number of tools in a specified sequence. Nothing in this test method should be construed as defining or establishing limits of acceptability for any grade or type of metal.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ASTM E431-96(2011) : Standard Guide to Interpretation of Radiographs of Semiconductors and Related Devices

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This guide provides illustrations of radiographs of semiconductors and related devices. Low powered transistors (through the TO-11 case configuration), diodes, low-power rectifiers, power devices, and integrated circuits are illustrated with common assembly features. Particular areas of construction are featured for these devices detailing critical points of design or assembly.

1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM E428-08(2013) : Standard Practice for Fabrication and Control of Metal, Other than Aluminum, Reference Blocks Used in Ultrasonic Testing

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This practice covers a procedure for fabrication and control of metal alloy reference blocks used in ultrasonic examination that have a flat-surface sound entry, are cylindrical in shape, and contain flat-bottom holes (FBH) which may be used for checking the performance of ultrasonic examination instrumentation and search units and for standardization and control of ultrasonic examination of metal alloy products. The reference blocks described are suitable for use with either the direct-contact method or immersion pulse-echo ultrasonic methods.

Note 1-Use of flat-surface reference blocks may not be suitable for cylindrical materials (3)².

1.2 While this procedure is basically designed for the fabrication and control of carbon and alloy steel blocks to be used in conjunction with the examination of these materials, the fabrication and control procedures may also be suitable for the preparation of blocks for other types of materials such as nickel-base alloys, certain types of aluminum alloys, and so forth. Additional procedures and controls may be required when fabricating reference blocks from other than carbon or alloy steel material. This practice shall in no way preclude the specification or addition of any supplemented requirements as deemed necessary for the specific application. This practice, however, must not be confused with, nor does it supersede Practice E127, specifically governing the fabrication and evaluation of 7075-T6 aluminum alloy ultrasonic standard reference blocks.

Note 2-Practice E127 and Guide E1158 also describe procedures for selecting material, fabricating blocks, and checking response. Unlike this practice, Practice E127 has requirements for evaluation relative to a specified standard target.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM E2751/E2751M-13 : Standard Practice for Design and Performance of Supported Laminated Glass Walkways

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This practice addresses elements related to load-bearing glass walkways, glass treads, and glass landings constructed with laminated glass. This standard includes performance, design, and safe behavior considerations. It addresses the characteristics unique to glass and laminated glass. Issues that are common to all walkways, such as slip resistance, are addressed in existing referenced standards.

1.2 This practice does not address glass walkways constructed with monolithic glass, glass block, insulating glass units, glass tiles that are directly bonded to a non-glass structural substrate, or glass walkways intended to support vehicular traffic.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

ASTM E1981-98(2012)e2 : Standard Guide for Assessing Thermal Stability of Materials by Methods of Accelerating Rate Calorimetry

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This guide covers suggested procedures for the operation of a calorimetric device designed to obtain temperature and pressure data as a function of time for systems undergoing a physicochemical change under nearly adiabatic conditions.

1.2 This guide outlines the calculation of thermodynamic parameters from the time, temperature, and pressure data recorded by a calorimetric device.

1.3 The assessment outlined in this guide may be used over a pressure range from full vacuum to the rated pressure of the reaction container and pressure transducer. The temperature range of the calorimeter typically varies from ambient to 500°C, but also may be user specified (see 6.6).

1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5 This statement does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety practices and to determine the applicability of regulatory limitations prior to use. Specific safety precautions are outlined in Section 7.

ASTM E1820-11e2 : Standard Test Method for Measurement of Fracture Toughness

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD (δ). Toughness can be measured in the R-curve format or as a point value. The fracture toughness determined in accordance with this test method is for the opening mode (Mode I) of loading.

1.2 The recommended specimens are single-edge bend, [SE(B)], compact, [C(T)], and disk-shaped compact, [DC(T)]. All specimens contain notches that are sharpened with fatigue cracks.

1.2.1 Specimen dimensional (size) requirements vary according to the fracture toughness analysis applied. The guidelines are established through consideration of material toughness, material flow strength, and the individual qualification requirements of the toughness value per values sought.

1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

Note 1-Other standard methods for the determination of fracture toughness using the parameters K, J, and CTOD are contained in Test Methods E399, E1290, and E1921. This test method was developed to provide a common method for determining all applicable toughness parameters from a single test.

ASTM E162-13 : Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This fire-test-response standard describes the measurement of surface flammability of materials. It is not intended for use as a basis of ratings for building code purposes (see Appendix X1).

1.3 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.

1.5 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. This test method may involve hazardous materials, operations, and equipment. Specific information about hazard is given in Section 7.

Note 1-There is no similar or equivalent ISO standard.

ASTM E125-63(2013) : Standard Reference Photographs for Magnetic Particle Indications on Ferrous Castings

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This collection of reference photographs covers types and degrees of discontinuities occurring in steel castings and other types of ferrous castings detectable by the dry powder magnetic particle method.

1.2 These reference photographs are intended to assist in the classification of those discontinuities revealed in ferrous castings subjected to magnetic particle examination.

1.3 These reference photographs are intended to be used for purposes of comparison with the magnetic particle indications observed on actual castings.

ASTM E1007-13 : Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This test method covers the measurement of the transmission of impact sound generated by a standard tapping machine through floor-ceiling assemblies and associated supporting structures in field situations.

1.2 Measurements may be conducted on all types of floor-ceiling assemblies, including those with floating-floor or suspended ceiling elements, or both, and floor-ceiling assemblies surfaced with any type of floor-surfacing or floor-covering materials.

1.3 This test method defines several procedures and metrics to assess either the apparent performance of the nominally separating floor-ceiling or the isolation of a receiving room from the sound produced by the operation of the tapping machine. The receiving room may be the space directly below the tapping machine or, in some cases, any separated space that receives sound from the operation of the tapping machine. The source and receiving rooms as well as the floor-ceiling system are identified and described in the test report. All measured levels and derivative single number ratings include the effect of flanking transmission. Efforts to suppress flanking are not permitted. Available measures and their single number ratings are the impact sound pressure levels (ISPL) and impact sound rating (ISR), the reverberation time normalized impact sound pressure levels (RTNISPL) and normalized impact sound rating (NISR), and the absorption normalized impact sound pressure levels (ANISPL) and apparent impact insulation class (AIIC).

1.4 The ISPL and ISR may be measured and reported between any two specific rooms or usage areas where the source room area is large enough to accommodate the tapping machine positions and the receiving room volume is sufficiently large to accommodate the microphone positions. For all other measures and ratings in this standard, restrictions such as minimum room volume or dimensions or maximum room absorption are imposed. Thus, conditions may exist that will not allow RTNISPL (NISR) or ANISPL (AIIC) to be measured.

1.5 Where a separating floor-ceiling assembly is composed of parts that are constructed differently on the receiving room (ceiling) side, it is not possible to measure the ANISPL and AIIC of the individual elements or portions of the assembly. In this situation, the measurement will be of the composite structure, not of an individual element.

1.6 Any single field measurement only represents the actual assembly tested and cannot be used alone to accurately predict how a similar assembly might perform.

1.7 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D7805-13 : Standard Terminology for Printing Ink Vehicles and Related Materials

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This standard contains the definitions of terms as used in reference to printing ink vehicles and related materials.

ASTM D7702/D7702M-13a : Standard Guide for Considerations When Evaluating Direct Shear Results Involving Geosynthetics

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This guide presents a summary of available information related to the evaluation of direct shear test results involving geosynthetic materials.

1.2 This guide is intended to assist designers and users of geosynthetics. This guide is not intended to replace education or experience and should only be used in conjunction with professional judgment. This guide is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project's many unique aspects. Not all aspects of this practice may be applicable in all circumstances. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.

1.3 This guide is applicable to soil-geosynthetic and geosynthetic-geosynthetic direct shear test results, obtained using either Test Method D5321 or D6243.

1.4 This guide does not address selection of peak or large-displacement shear strength values for design. References on this topic include Thiel (1)², Gilbert (2), Koerner and Bowman (3), and Stark and Choi (4).

1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

ASTM D7611/D7611M-13 : Standard Practice for Coding Plastic Manufactured Articles for Resin Identification

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This practice stipulates the types, names, and sizes of Codes for those material types specified in Table 1.

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are likely not to be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems is likely to result in non-conformance with the standard.

Note 1-There is no known ISO equivalent to this standard.

ASTM D7566-13 : Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This specification covers the manufacture of aviation turbine fuel that consists of conventional and synthetic blending components.

1.2 This specification applies only at the point of batch origination, as follows:

1.2.1 Aviation turbine fuel manufactured, certified, and released to all the requirements of Table 1 of this specification (D7566), meets the requirements of Specification D1655 and shall be regarded as Specification D1655 turbine fuel. Duplicate testing is not necessary; the same data may be used for both D7566 and D1655 compliance. Once the fuel is released to this specification (D7566) the unique requirements of this specification are no longer applicable: any recertification shall be done in accordance with Table 1 of Specification D1655.

1.2.2 Field blending of synthesized paraffinic kerosine (SPK) blendstocks, as described in Annex A1 (FT SPK) or Annex A2 (HEFA SPK) with D1655 fuel (which may on the whole or in part have originated as D7566 fuel) shall be considered batch origination in which case all of the requirements of Table 1 of this specification (D7566) apply and shall be evaluated. Short form conformance test programs commonly used to ensure transportation quality are not sufficient. The fuel shall be regarded as D1655 turbine fuel after certification and release as described in 1.2.1.

1.2.3 Once a fuel is redesignated as D1655 aviation turbine fuel, it can be handled in the same fashion as the equivalent refined D1655 aviation turbine fuel.

1.3 This specification defines specific types of aviation turbine fuel that contain synthesized hydrocarbons for civil use in the operation and certification of aircraft and describes fuels found satisfactory for the operation of aircraft and engines. The specification is intended to be used as a standard in describing the quality of aviation turbine fuels and synthetic blending components at the place of manufacture but can be used to describe the quality of aviation turbine fuels for contractual transfer at all points in the distribution system.

1.4 This specification does not include all fuels satisfactory for aviation turbine engines. Certain equipment or conditions of use may permit a wider, or require a narrower, range of characteristics than is shown by this specification.

1.5 While aviation turbine fuels defined by Table 1 of this specification can be used in applications other than aviation turbine engines, requirements for such other applications have not been considered in the development of this specification.

1.6 Synthetic blending components, synthetic fuels, and blends of synthetic fuels with conventional petroleum-derived fuels in this specification have been evaluated and approved in accordance with the principles established in Practice D4054.

1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D7549-13 : Standard Test Method for Evaluation of Heavy-Duty Engine Oils under High Output Conditions—Caterpillar C13 Test Procedure

Wed, 19 Jun 2013 13:30:39 -0500

1.1 The test method covers a heavy-duty engine test procedure under high output conditions to evaluate engine oil performance with regard to piston deposit formation, piston ring sticking and oil consumption control in a combustion environment designed to minimize exhaust emissions. This test method is commonly referred to as the Caterpillar C13 Heavy-Duty Engine Oil Test.³

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1 Exceptions-Where there are no SI equivalent such as screw threads, National Pipe Treads (NPT), and tubing sizes.

ASTM D7422-13 : Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including lead corrosion and wear of piston rings and cylinder liners in an engine equipped with exhaust gas recirculation and running on ultra-low sulfur diesel fuel.² This test method is commonly referred to as the Mack T-12.

1.1.1 This test method also provides the procedure for running an abbreviated length test, which is commonly referred to as the T-12A. The procedures for the T-12 and T-12A are identical with the exception of the items specifically listed in Annex A9. Additionally, the procedure modifications listed in Annex A9 refer to the corresponding section of the T-12 procedure.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1 Exception-Where there is no direct SI equivalent, such as the units for screw threads, National Pipe Threads/diameters, tubing size, and single source supply equipment specifications.

ASTM D7419-13 : Standard Test Method for Determination of Total Aromatics and Total Saturates in Lube Basestocks by High Performance Liquid Chromatography (HPLC) with Refractive Index Detection

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This test method covers the determination of total aromatics and total saturates in additive-free lube basestocks using high performance liquid chromatography (HPLC) with refractive index (RI) detection. This test method is applicable to samples containing total aromatics in the concentration range of 0.2 to 46 mass %.

1.1.1 Polar compounds, if present, are combined with the total aromatics. Precision was determined for basestocks with polars content < 1.0 mass %.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

ASTM D7273/D7273M-08(2013)e1 : Standard Guide for for Acceptance Testing Requirements for Geonets and Geonet Drainage Geocomposites

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This guide covers guidelines for the acceptance testing frequency requirements for geonet and geonet drainage geocomposite materials describing types of tests, test methods, and recommended verifications.

1.2 This guide is intended to aid purchasers, installers, contractors, owners, operators, designers, and agencies in establishing a minimum level of effort for product acceptance testing and verification. This is intended to assure that the supplied geonet and/or geonet drainage geocomposite roll(s) meet accepted material specifications.

1.3 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This guide cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This guide is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this guide be applied without consideration of a project's many unique aspects. The word "Standard" in the title of this guide means only that the guide has been approved through the ASTM International consensus process.

1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

ASTM D7004/D7004M-03(2013)e1 : Standard Test Method for Grab Tensile Properties of Reinforced Geomembranes

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This test method is used to measure the grab tensile properties of reinforced geomembranes.

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

ASTM D7003/D7003M-03(2013)e1 : Standard Test Method for Strip Tensile Properties of Reinforced Geomembranes

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This test method is used to measure the strip tensile properties of reinforced geomembranes.

ASTM D6750-13 : Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4?% Fuel Sulfur) and 1N Procedure (0.04?% Fuel Sulfur)

Wed, 19 Jun 2013 13:30:39 -0500

1.1 These test methods cover the performance of engine oils intended for use in certain diesel engines. They are performed in a standardized high-speed, single-cylinder diesel engine by either the 1K (0.4 % mass fuel sulfur) or 1N (0.04 % mass fuel sulfur) procedure.³ The only difference in the two test methods is the fuel used. Piston and ring groove deposit-forming tendency and oil consumption are measured. Also, the piston, the rings, and the liner are examined for distress and the rings for mobility. These test methods are required to evaluate oils intended to satisfy API service categories CF-4 and CH-4 for 1K, and CG-4 for 1N of Specification D4485.

1.2 These test methods, although based on the original Caterpillar 1K/1N procedures,³ also embody TMC information letters issued before these test methods were first published. These test methods are subject to frequent change. Until the next revision of these test methods, TMC will update changes in these test methods by the issuance of information letters which shall be obtained from TMC (see Annex A15).

1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3.1 Exception-Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing size, or single source equipment specified. Also Brake Specific Fuel Consumption is measured in kilograms per kilowatthour.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements appear throughout the text. Being engine tests, these test methods do have definite hazards that shall be met by safe practices (see Annex A16 on Safety Precautions).

1.5 The following is the Table of Contents:

		Section
Introduction
Scope		1
Referenced documents		2
Terminology		3
Summary of Test Methods		4
Significance and Use		5
Apparatus		6
	General Laboratory Requirements	6.1
	Test Engine	6.2
	Test Engine Accessories and Parts	6.3
Reagents and Materials		7
Test Oil Sample Requirements		8
Preparation of Apparatus		9
	Engine Inspection	9.1
	Engine Pre-Test Lubrication System Flush	9.2
	Engine Pre-Test Measurements and Inspections	9.3
	Engine Assembly	9.4
	Pressure Testing of Fuel System Assembly	9.5
Calibration of Engine Test Stand		10
	General Requirements and Frequency of Calibration	10.1
	Runs	10.2
	Specified Test Parameters	10.3
	Calibration Test Acceptance Criteria	10.4
	Action on Rejection of Calibration Test	10.5
	Test Numbering	10.6
	Reference Oils	10.7
	Severity Adjustments	10.8
Engine Operating Procedure		11
	Engine Run-In	11.1
	Cool-Down Procedure	11.2
	Warm-Up Procedure	11.3
	Operating Conditions and Oil Additions	11.4
	Measurement of Oil Consumption	11.5
	Sampling Used Oil	11.6
	Shutdowns, Lost Time and Off Tolerance Conditions	11.7
	Recording of Exhaust Temperature	11.8
	Air-Fuel Ratio Measurement	11.9
	Recording of Engine Conditions	11.10
	Humidity Requirements/Calibration/Measurement	11.11
Inspections, Photographs and Measurements		12
	Reference to Reporting Form	12.1
	Pre-Test Measurements of Engine Parts	12.2
	Post-Test Information	12.3
	Oil Inspections	12.4
Report		13
	General Directions	13.1
	Electronic Transmission of Test Results (Optional)	13.2
	Reporting Calibration Test Results	13.3
Precision and Bias		14
Keywords		15
	ANNEXES
Specifications for Test Engine and Engine Build		Annex A1
Intake Air System Details		Annex A2
Exhaust System Details		Annex A3
Cooling System Details		Annex A4
Oil System Modifications and Instrument Locations		Annex A5
Other Pressure and Temperature Measurement Locations		Annex A6
Oil Consumption Linear Regression Method		Annex A7
Test Fuel Specifications		Annex A8
Lubrication System, Flush Apparatus and Procedure		Annex A9
Engine Operating Conditions		Annex A10
Procedure for Rating Piston and Liner		Annex A11
Calculation of Percent Offset and Percent Deviation		Annex A12
1K/1N Test Reporting		Annex A13
Parts List by Part Number (P/N) and Warranty		Annex A14
Role of Test Monitoring Center		Annex A15
Safety Precautions		Annex A16
	APPENDIXES
Humidity Data		Appendix X1
Statistical Equations for Mean and Standard Deviation		Appendix X2
Examples of Forms for Reporting		Appendix X3
Optional Recording of Oil Pass Limits		Appendix X4

ASTM D6708-13 : Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This practice covers statistical methodology for assessing the expected agreement between two standard test methods that purport to measure the same property of a material, and deciding if a simple linear bias correction can further improve the expected agreement. It is intended for use with results collected from an interlaboratory study meeting the requirement of Practice D6300 or equivalent (for example, ISO 4259 ). The interlaboratory study must be conducted on at least ten materials that span the intersecting scopes of the test methods, and results must be obtained from at least six laboratories using each method.

1.2 The statistical methodology is based on the premise that a bias correction will not be needed. In the absence of strong statistical evidence that a bias correction would result in better agreement between the two methods, a bias correction is not made. If a bias correction is required, then the parsimony principle is followed whereby a simple correction is to be favored over a more complex one.

Note 1-Failure to adhere to the parsimony principle generally results in models that are over-fitted and do not perform well in practice.

1.3 The bias corrections of this practice are limited to a constant correction, proportional correction or a linear (proportional + constant) correction.

1.4 The bias-correction methods of this practice are method symmetric, in the sense that equivalent corrections are obtained regardless of which method is bias-corrected to match the other.

1.5 A methodology is presented for establishing the 95 % confidence limit (designated by this practice as the between methods reproducibility) for the difference between two results where each result is obtained by a different operator using different apparatus and each applying one of the two methods X and Y on identical material, where one of the methods has been appropriately bias-corrected in accordance with this practice.

Note 2-In earlier versions of this standard practice, the term “cross-method reproducibility” was used in place of the term “between methods reproducibility.” The change was made because the “between methods reproducibility” term is more intuitive and less confusing. It is important to note that these two terms are synonymous and interchangeable with one another, especially in cases where the “cross-method reproducibility” term was subsequently referenced by name in methods where a D6708 assessment was performed, before the change in terminology in this standard practice was adopted.

Note 3-Users are cautioned against applying the between methods reproducibility as calculated from this practice to materials that are significantly different in composition from those actually studied, as the ability of this practice to detect and address sample-specific biases (see 6.8) is dependent on the materials selected for the interlaboratory study. When sample-specific biases are present, the types and ranges of samples may need to be expanded significantly from the minimum of ten as specified in this practice in order to obtain a more comprehensive and reliable 95 % confidence limits for between methods reproducibility that adequately cover the range of sample specific biases for different types of materials.

1.6 This practice is intended for test methods which measure quantitative (numerical) properties of petroleum or petroleum products.

1.7 The statistical methodology outlined in this practice is also applicable for assessing the expected agreement between any two test methods that purport to measure the same property of a material, provided the results are obtained on the same comparison sample set, the standard error associated with each test result is known, the sample set design meets the requirement of this practice, and the statistical degree of freedom of the data set exceeds 30.

ASTM D6298-13 : Standard Specification for Fiberglass Reinforced Styrene-Butadiene-Styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This specification covers fiberglass reinforced modified bituminous sheet materials that use styrene-butadiene-styrene (SBS) thermoplastic elastomer as the primary modifier and are surfaced with a factory applied continuous metal foil. These materials are intended for use in the fabrication of multiple ply roofing and waterproofing membranes and flashings.

1.2 This specification is intended as a material specification only. Questions regarding the suitability of the specific roof constructions or application techniques are beyond the scope of this specification.

1.3 The specified tests and property limits are intended to establish minimum properties. In place roof system design criteria such as fire resistance, field strength, impact/puncture resistance, material compatibility, uplift resistance, and others, are factors beyond the scope of this specification.

1.4 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.

1.5 The following precautionary statement pertains to the test method portion only, Section 8 of this Specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D6294/D6294M-13 : Standard Test Method for Corrosion Resistance of Ferrous Metal Fastener Assemblies Used in Roofing and Waterproofing

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This test method covers components of ferrous metal fastener assemblies, excluding those of stainless steel, such as fasteners, stress plates, and batten bars used in low slope roofing and waterproofing, to a sulfurous acid environment. This test method evaluates relative corrosion resistance of the components by determination of percentage of rust or white rust.

1.2 The components may or may not have a surface treatment applied.

1.3 A limiting factor is the subjectiveness when determining actual percentage of rust or white rust corrosion.

1.4 Other performance characteristics of ferrous metal components such as abrasion resistance of barrier coatings are not evaluated in this method.

1.5 This test method was developed based on Practice G87.

1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

ASTM D6214/D6214M-98(2013)e1 : Standard Test Method for Determining the Integrity of Field Seams Used in Joining Geomembranes by Chemical Fusion Methods

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This test method covers an accelerated, destructive test method for geomembranes in a geotechnical application.

1.2 This test is applicable to field fabricated geomembranes that are scrim reinforced or non reinforced.

1.3 This test method is applicable for field seaming processes that use a chemical fusion agent or bodied chemical fusion agent, as the seaming mechanism.

1.4 Subsequent decisions as to seam acceptance criteria are made according to the site-specific contract plans, specification and CQC/CQA documents.

1.6 Hazardous Materials-Always consult the proper Material Safety Data Sheets for any Hazardous materials used for proper ventilation and protection. The use of the oven in this test method may accelerate fume production from the test specimen.

ASTM D6122-13 : Standard Practice for Validation of the Performance of Multivariate Online, At-Line, and Laboratory Infrared Spectrophotometer Based Analyzer Systems

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This practice covers requirements for the validation of measurements made by laboratory or process (online or at-line) near- or mid-infrared analyzers, or both, used in the calculation of physical, chemical, or quality parameters (that is, properties) of liquid petroleum products. The properties are calculated from spectroscopic data using multivariate modeling methods. The requirements include verification of adequate instrument performance, verification of the applicability of the calibration model to the spectrum of the sample under test, and verification of equivalence between the result calculated from the infrared measurements and the result produced by the primary test method used for the development of the calibration model. When there is adequate variation in property level, the statistical methodology of Practice D6708 is used to provide general validation of this equivalence over the complete operating range of the analyzer. For cases where there is inadequate property variation, methodology for level specific validation is used.

1.2 Performance Validation is conducted by calculating the precision and bias of the differences between results from the analyzer system (or subsystem) produced by application of the multivariate model, (such results are herein referred to as Predicted Primary Test Method Results (PPTMRs)), versus the Primary Test Method Results (PTMRs) for the same sample set. Results used in the calculation are for samples that are not used in the development of the multivariate model. The calculated precision and bias are statistically compared to user-specified requirements for the analyzer system application.

1.2.1 For analyzers used in product release or product quality certification applications, the precision and bias requirement for the degree of agreement are typically based on the site or published precision of the Primary Test Method.

Note 1-In most applications of this type, the PTM is the specification-cited test method.

1.2.2 This practice does not describe procedures for establishing precision and bias requirements for analyzer system applications. Such requirements must be based on the criticality of the results to the intended business application and on contractual and regulatory requirements. The user must establish precision and bias requirements prior to initiating the validation procedures described herein.

1.3 This practice does not cover procedures for establishing the calibration model (correlation) used by the analyzer. Calibration procedures are covered in Practices E1655 and references therein.

1.4 This practice is intended as a review for experienced persons. For novices, this practice will serve as an overview of techniques used to verify instrument performance, to verify model applicability to the spectrum of the sample under test, and to verify equivalence between the parameters calculated from the infrared measurement and the results of the primary test method measurement.

1.5 This practice teaches and recommends appropriate statistical tools, outlier detection methods, for determining whether the spectrum of the sample under test is a member of the population of spectra used for the analyzer calibration. The statistical tools are used to determine if the infrared measurement results in a valid property or parameter estimate.

1.6 The outlier detection methods do not define criteria to determine whether the sample or the instrument is the cause of an outlier measurement. Thus, the operator who is measuring samples on a routine basis will find criteria to determine that a spectral measurement lies outside the calibration, but will not have specific information on the cause of the outlier. This practice does suggest methods by which instrument performance tests can be used to indicate if the outlier methods are responding to changes in the instrument response.

1.7 This practice is not intended as a quantitative performance standard for the comparison of analyzers of different design.

1.8 Although this practice deals primarily with validation of infrared analyzers, the procedures and statistical tests described herein are also applicable to other types of analyzers which employ multivariate models.

ASTM D5961/D5961M-13 : Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This test method covers the bearing response of pinned or fastened joints using multi-directional polymer matrix composite laminates reinforced by high-modulus fibers by double-shear tensile loading (Procedure A), single-shear tensile or compressive loading of a two-piece specimen (Procedure B), single-shear tensile loading of a one-piece specimen (Procedure C), or double-shear compressive loading (Procedure D). Standard specimen configurations using fixed values of test parameters are described for each procedure. However, when fully documented in the test report, a number of test parameters may be optionally varied. The composite material forms are limited to continuous-fiber or discontinuous-fiber (tape or fabric, or both) reinforced composites for which the laminate is balanced and symmetric with respect to the test direction. The range of acceptable test laminates and thicknesses are described in 8.2.1.

1.2 This test method is consistent with the recommendations of MIL-HDBK-17 , which describes the desirable attributes of a bearing response test method.

1.3 The multi-fastener test configurations described in this test method are similar to those used by industry to investigate the bypass portion of the bearing bypass interaction response for bolted joints, where the specimen may produce either a bearing failure mode or a bypass failure mode. Note that the scope of this test method is limited to bearing and fastener failure modes. Use Test Method D7248/D7248M for by-pass testing.

1.4.1 Within the text the inch-pound units are shown in brackets.

ASTM D5895-13 : Standard Test Methods for Evaluating Drying or Curing During Film Formation of Organic Coatings Using Mechanical Recorders

Wed, 19 Jun 2013 13:30:39 -0500

1.1 These test methods describe the determination of several stages and the rate of dry-film formation of organic coatings using straight line and circular mechanical drying-time recording devices. The use of mechanical recorders is valuable in comparing the drying behavior of coatings of the same generic type, allowing that one coating may form a gel or resist tearing at a faster rate than another.

1.2 Drying time measured using the mechanical recorders may differ from those found using conventional methods, such as Test Method D1640 or ISO 9117-3 (formerly ISO 1517).

1.3 The values stated in SI are to be regarded as the standard. The values given in parentheses are provided for information only.

ASTM D5798-13 : Standard Specification for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark-Ignition Engines

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This specification covers the requirements for automotive fuel blends of ethanol and gasoline for use in ground vehicles equipped with ethanol fuel blend flexible-fuel spark-ignition engines. Fuel produced to this specification contains 51 to 83 volume % ethanol. This fuel is for use in flexible-fuel vehicles and is sometimes referred to at retail as “Ethanol Flex-Fuel.” Appendix X1 discusses the significance of the properties specified.

1.2 The vapor pressure of ethanol fuel blends is varied for seasonal climatic changes. Vapor pressure is increased at lower temperatures to ensure adequate flexible-fuel vehicle operability. Ethanol content and selection of hydrocarbon blendstock are adjusted by the blender to meet these vapor pressure requirements.

1.3 This specification formerly covered Fuel Ethanol (Ed70-Ed85) for Automotive Spark-Ignition Engines, also known commercially as E85. The nomenclature “fuel ethanol” has been changed to “ethanol fuel blends” to distinguish this product from denatured fuel ethanol Specification D4806. To facilitate blending of ethanol fuel blends that meet seasonal vapor pressure requirements, a new lower minimum ethanol content has been established.

1.4 The United States government has established various programs for alternative fuels. Many of the definitions of alternative fuel used by these programs may be more restrictive than the requirements of this specification. See 4.1.2.1 for additional information on alternative fuels containing ethanol.

1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.6 The following safety hazard caveat pertains only to the test method portion, 8.1.8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D5747/D5747M-08(2013)e1 : Standard Practice for Tests to Evaluate the Chemical Resistance of Geomembranes to Liquids

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This practice covers procedures for the testing of geomembranes for chemical resistance with liquid wastes, prepared chemical solutions, and leachates derived from solid wastes.

1.2 This practice covers procedures for testing semi-crystalline, amorphous, elastomeric, and fabric-reinforced geomembranes.

1.3 This practice is intended to be used in conjunction with Practice D5322 or Practice D5496, or both. The scope of this practice is limited to testing and reporting procedures for unexposed and exposed geomembrane samples.

1.4 Evaluation and interpretation of test data are beyond the scope of this practice.

ASTM D4833/D4833M-07(2013)e1 : Standard Test Method for Index Puncture Resistance of Geomembranes and Related Products

Wed, 19 Jun 2013 13:30:39 -0500

1.1 This test method is used to measure the index puncture resistance of geomembranes and related products.

1.2 The use of Test Method D4833/D4833M may be inappropriate for testing some woven geotextiles or related products which have large openings, such as geonets and geogrids.

1.3 It is recommended that geotextile and geotextile related products be tested using Test Method D6241.

ASTM B299-13 : Standard Specification for Titanium Sponge

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers the purchase of virgin titanium sponge metal. This virgin metal is commonly designated as titanium sponge because it is most commonly porous and sponge-like in texture, although metal produced electrolytically is granular and is essentially nonporous.

ASTM D4437-08(2013) : Standard Practice for Non-destructive Testing (NDT) for Determining the Integrity of Seams Used in Joining Flexible Polymeric Sheet Geomembranes

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This practice is intended for use as a summary of nondestructive quality control test methods for determining the integrity of seams used in the joining of flexible sheet materials in a geotechnical application. This practice outlines the test procedures available for determining the quality of bonded seams. Any one or combination of the test methods outlined in this practice can be incorporated into a project specification for quality control. These test methods are applicable to manufactured flexible polymeric membrane linings that are scrim reinforced or nonreinforced. This practice is not applicable to destructive testing. For destructive test methods look at other ASTM Standards and Practices.

1.2 The types of seams covered by this practice include the following: Thermally Bonded Seams, Hot Air, Hot Wedge (or Knife), Extrusion, Solvent Bonded Seams, Bodied Solvent Bonded Seams, Adhesive Bonded or Cemented Seams, Taped Seams, Waterproofed Sewn Seams.

1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D3764-13 : Standard Practice for Validation of the Performance of Process Stream Analyzer Systems

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This practice describes procedures and methodologies based on the statistical principles of Practice D6708 to validate whether the degree of agreement between the results produced by a total analyzer system (or its subsystem), versus the results produced by an independent test method that purports to measure the same property, meets user-specified requirements. This is a performance-based validation, to be conducted using a set of materials that are not used a priori in the development of any correlation between the two measurement systems under investigation. A result from the independent test method is herein referred to as a Primary Test Method Result (PTMR).

1.2 This practice assumes any correlation necessary to mitigate systemic biases between the analyzer system and PTM have been applied to the analyzer results. See Guide D7235 for procedures for establishing such correlations.

1.3 This practice requires that both the primary method against which the analyzer is compared to, and the analyzer system under investigation, are in statistical control. Practices described in Practice D6299 should be used to ensure this condition is met.

1.4 This practice applies if the process stream analyzer system and the primary test method are based on the same measurement principle(s), or, if the process stream analyzer system uses a direct and well-understood measurement principle that is similar to the measurement principle of the primary test method. This practice also applies if the process stream analyzer system uses a different measurement technology from the primary test method, provided that the calibration protocol for the direct output of the analyzer does not require use of the PTMRs (see Case 1 in Note 1).

1.5 This practice does not apply if the process stream analyzer system utilizes an indirect or mathematically modeled measurement principle such as chemometric or multivariate analysis techniques where PTMRs are required for the chemometric or multivariate model development. Users should refer to Practice D6122 for detailed validation procedures for these types of analyzer systems (see Case 2 in Note 1).

Note 1-For example, for the measurement of benzene in spark ignition fuels, comparison of a Mid-Infrared process analyzer system based on Test Method D6277 to a Test Method D3606 gas chromatography primary test method would be considered Case 1, and this practice would apply. For each sample, the Mid-Infrared spectrum is converted into a single analyzer result using methodology (Test Method D6277) that is independent of the primary test method (Test Method D3606). However, when the same analyzer uses a multivariate model to correlate the measured Mid-Infrared spectrum to Test Method D3606 reference values using the methodology of Practice E1655, it is considered Case 2 and Practice D6122 applies. In this case 2 example, the direct output of the analyzer is the spectrum, and the conversion of this multivariate output to an analyzer result require use of Practice D6122, hence it is not independent of the primary test method.

1.6 Performance Validation is conducted by calculating the precision and bias of the differences between results from the analyzer system (or subsystem) after the application of any necessary correlation, (such results are herein referred to as Predicted Primary Test Method Results (PPTMRs)), versus the PTMRs for the same sample set. Results used in the calculation are for samples that are not used in the development of the correlation. The calculated precision and bias are statistically compared to user-specified requirements for the analyzer system application.

1.6.1 For analyzers used in product release or product quality certification applications, the precision and bias requirement for the degree of agreement are typically based on the site or published precision of the Primary Test Method.

Note 2-In most applications of this type, the PTM is the specification-cited test method.

1.6.2 This practice does not describe procedures for establishing precision and bias requirements for analyzer system applications. Such requirements must be based on the criticality of the results to the intended business application and on contractual and regulatory requirements. The user must establish precision and bias requirements prior to initiating the validation procedures described herein.

1.7 Two procedures for validation are described: the line sample procedure and the validation reference material (VRM) injection procedure.

1.8 Only the analyzer system or subsystem downstream of the VRM injection point or the line sample extraction point is being validated by this practice.

1.9 The line sample procedure is limited to applications where material can be safely withdrawn from the sampling point of the analyzer unit without significantly altering the property of interest.

1.10 Validation information obtained in the application of this practice is applicable only to the type and property range of the materials used to perform the validation.

1.11 Two types of validation are described: General Validation, and Level Specific Validation. These are typically conducted at installation or after major maintenance once the system mechanical fitness-for-use has been established.

1.11.1 General Validation is based on the statistical principles and methodology of Practice D6708. In most cases, General Validation is preferred, but may not always be possible if the variation in validation materials is insufficient. General Validation will validate analyzer operation over a wider operating range than Level Specific Validation.

1.11.2 When the variation in available validation materials is insufficient to satisfy the requirements of Practice D6708, a Level Specific Validation is done to validate analyzer operation over a limited range.

1.11.3 The validation outcome are considered valid only within the range covered by the validation material Data from several different Validations (general or level-specific) can potentially be combined for use in a General Validation.

1.12 Procedures for the continual validation of system performance are described. These procedures are typically applied at a frequency commensurate with the criticality of the application.

1.13 This practice does not address procedures for diagnosing causes of validation failure.

1.14 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D3636-13a : Standard Practice for Sampling and Judging Quality of Solid Electrical Insulating Materials

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This practice covers procedures for obtaining data pertaining to the quality of a lot of electrical insulating material and for making a judgement whether the lot meets the requirements of a material specification.

1.2 This practice is not intended to define a producer's internal quality control procedures but is designed to determine the acceptability of all, or some portion, of a quantity of electrical insulating material that is available for inspection by the user of the material.

1.3 This practice is intended to be used in conjunction with an existing material specification that specifies property characteristic limits, acceptable quality level (AQL), standard test methods, and specific sampling instructions.

1.4 In the absence of a specification as described in 1.3, use this practice as a guide, after establishment of agreed-upon property characteristics, limits, AQL, standard test methods, and specific sampling instructions.

1.5 It is intended that this be a practice for inspection by attributes.

ASTM D2887-13 : Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This test method covers the determination of the boiling range distribution of petroleum products. The test method is applicable to petroleum products and fractions having a final boiling point of 538°C (1000°F) or lower at atmospheric pressure as measured by this test method. This test method is limited to samples having a boiling range greater than 55.5°C (100°F), and having a vapor pressure sufficiently low to permit sampling at ambient temperature.

Note 1-Since a boiling range is the difference between two temperatures, only the constant of 1.8°F/°C is used in the conversion of the temperature range from one system of units to another.

1.1.1 Procedure A (Sections 6-14)-Allows a larger selection of columns and analysis conditions such as packed and capillary columns as well as a Thermal Conductivity Detector in addition to the Flame Ionization Detector. Analysis times range from 14 to 60 min.

1.1.2 Procedure B (Sections 15-23)-Is restricted to only 3 capillary columns and requires no sample dilution. In addition, Procedure B is used not only for the sample types described in Procedure A but also for the analysis of samples containing biodiesel mixtures B5, B10, and B20. The analysis time, when using Procedure B (Accelerated D2887), is reduced to about 8 min.

1.2 This test method is not to be used for the analysis of gasoline samples or gasoline components. These types of samples must be analyzed by Test Method D3710.

1.3 The values stated in SI units are to be regarded as standard. The inch-pound units given in parentheses are for information only.

ASTM D2643/D2643M-08(2013)e1 : Standard Specification for Prefabricated Bituminous Geomembrane Used as Canal and Ditch Liner (Exposed Type)

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers prefabricated bituminous geomembranes intended to provide a continuous, exposed lining for canals and ditches.

ASTM D2513-13 : Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas mains and services for direct burial and reliner applications. The pipe and fittings covered by this specification are intended for use in the distribution of natural gas. Requirements for the qualifying of polyethylene systems for use with liquefied petroleum gas are also covered.

1.1.1 This specification does not cover threaded pipe. Design considerations are discussed in Appendix X1. In-plant quality control programs are specified in Annex A1 and Annex A2.

1.1.2 See Specification F2619/F2619M for polyethylene piping for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water.

1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

1.4 The following is an index of the annexes and appendix in this specification:

Annex	Subject
Annex A1	In-Plant Quality Control for all materials up to 12 in.
Annex A2	In-Plant Quality Control for PE materials 14 in. and larger.

Appendixes	Subject
Appendix X1	Design Consideration

1.5 The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D2303-13 : Standard Test Methods for Liquid-Contaminant, Inclined-Plane Tracking and Erosion of Insulating Materials

Wed, 19 Jun 2013 13:30:38 -0500

1.1 These test methods cover the evaluation of the relative tracking and erosion resistance of insulating solids using the liquid-contaminant, inclined-plane test.² The following test methods also can be used to evaluate the tracking resistance of materials: D2132 (contaminants: dust and fog) and D3638 (contaminant: conductive liquid drops).

1.2 Two tracking and one erosion test procedure are described:

1.2.1 A “variable voltage method” to evaluate resistance to tracking.

1.2.2 A “time-to-track method” to evaluate resistance to tracking.

1.2.3 A method for quantitative determination of erosion (Annex A1).

1.3 While a particular contaminant solution is specified, other concentrations of the same contaminant, or different contaminants are used to simulate different environmental or service conditions.

1.4 The values stated in inch-pound units are to be regarded as the standard.

ASTM D1655-13 : Standard Specification for Aviation Turbine Fuels

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers the use of purchasing agencies in formulating specifications for purchases of aviation turbine fuel under contract.

1.2 This specification defines specific types of aviation turbine fuel for civil use in the operation and certification of aircraft and describes fuels found satisfactory for the operation of aircraft and engines. The specification can be used as a standard in describing the quality of aviation turbine fuels from the refinery to the aircraft.

1.3 This specification does not include all fuels satisfactory for aviation turbine engines. Certain equipment or conditions of use may permit a wider, or require a narrower, range of characteristics than is shown by this specification.

1.4 Aviation turbine fuels defined by this specification may be used in other than turbine engines that are specifically designed and certified for this fuel.

1.5 This specification no longer includes wide-cut aviation turbine fuel (Jet B). FAA has issued a Special Airworthiness Information Bulletin which now approves the use of Specification D6615 to replace Specification D1655 as the specification for Jet B and refers users to this standard for reference.

1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

ASTM D1319-13 : Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This test method covers the determination of hydrocarbon types over the concentration ranges from 5 to 99 volume % aromatics, 0.3 to 55 volume % olefins, and 1 to 95 volume % saturates in petroleum fractions that distill below 315°C. This test method may apply to concentrations outside these ranges, but the precision has not been determined. Samples containing dark-colored components that interfere in reading the chromatographic bands cannot be analyzed.

Note 1-For the determination of olefins below 0.3 volume %, other test methods are available, such as Test Method D2710.

1.2 This test method is intended for use with full boiling range products. Cooperative data have established that the precision statement does not apply to narrow boiling petroleum fractions near the 315°C limit. Such samples are not eluted properly, and results are erratic.

1.3 The applicability of this test method to products derived from fossil fuels other than petroleum, such as coal, shale, or tar sands, has not been determined, and the precision statement may or may not apply to such products.

1.4 This test method has two precision statements depicted in tables. The first table is applicable to unleaded fuels that do not contain oxygenated blending components. It may or may not apply to automotive gasolines containing lead antiknock mixtures. The second table is applicable to oxygenate blended (for example, MTBE, ethanol) automotive spark ignition fuel samples with a concentration range of 13-40 volume percent aromatics, 4-33 volume percent olefins, and 45-68 volume percent saturates.

1.5 The oxygenated blending components, methanol, ethanol, methyl-tert-butylether (MTBE), tert-amylmethylether (TAME), and ethyl-tert-butylether (ETBE), do not interfere with the determination of hydrocarbon types at concentrations normally found in commercial blends. These oxygenated components are not detected since they elute with the alcohol desorbent. Other oxygenated compounds shall be individually verified. When samples containing oxygenated blending components are analyzed, correct the results to a total-sample basis.

1.6 WARNING-Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA's website-http://www.epa.gov/mercury/faq.htm-for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.

1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

ASTM D1227-13 : Standard Specification for Emulsified Asphalt Used as a Protective Coating for Roofing

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers emulsified asphalt suitable for use as a protective coating for built-up roofs and other exposed surfaces with inclines of not less than 4 % or 42 mm/m (¹/₂ in./ft).

ASTM C728-13 : Standard Specification for Perlite Thermal Insulation Board

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers the composition and physical properties for perlite thermal insulation board used principally above structural roof decks and as a base for built-up, modified, and elastomeric membrane roofing in building construction.

1.2 When adopted by an authority having jurisdiction, codes that address fire properties in many applications regulate the use of the thermal insulation materials covered by this specification. Fire properties are controlled by job, project, or other specifications where codes or government regulations do not apply.

ASTM C1767-13 : Standard Specification for Stainless Steel Jacketing for Insulation

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc, galvanized steel, or aluminized steel) nor does it cover the details of thermal, acoustical, or fire protective insulation systems.

1.2 While not intended to cover use inside the containment buildings of nuclear power plants, this standard does not preclude use of Class E material which does not have a moisture barrier in this containment building application.

1.3 This specification provides physical requirements for stainless steel jacketing for thermal and acoustical insulation. Guide C1423 provides guidance in selecting jacketing materials and their safe use.

1.4 This is a material specification and does not imply any performance of the installed system using the materials specified herein. For information about installation of stainless steel jacketing, see (1).²

ASTM C1729-13 : Standard Specification for Aluminum Jacketing for Insulation

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers aluminum jacketing for thermal and acoustical insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other materials such as mastics, fiber reinforced plastic, PVC, or stainless steel nor does it cover the details of thermal or acoustical insulation systems.

1.2 This specification provides physical requirements for aluminum jacketing for thermal and acoustical insulation. Guide C1423 provides guidance in selecting jacketing materials and their safe use.

1.3 This is a material specification and does not imply any performance of the installed system using the materials specified herein. For information about installation of aluminum jacketing, see (1).²

ASTM C1668-13 : Standard Specification for Externally Applied Reflective Insulation Systems on Rigid Duct in Heating, Ventilation, and Air Conditioning (HVAC) Systems

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers the requirements and physical properties of reflective insulation systems applied externally to Rigid Heating, Ventilation, and Air Conditioning (HVAC) duct systems operating at or below 250ºF (121.1 °C). These insulation systems consist of one or more low-emittance surfaces, such as metallic foil or metallic deposits, mounted on substrates to produce reflective air spaces. Reflective insulation systems derive thermal performance from surfaces with an emittance of no greater than 0.1 facing enclosed air spaces.

ASTM C138/C138M-13 : Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This test method covers determination of the density (see Note 1) of freshly mixed concrete and gives formulas for calculating the yield, cement content, and air content of the concrete. Yield is defined as the volume of concrete produced from a mixture of known quantities of the component materials.

Note 1-Unit weight was the previous terminology used to describe the property determined by this test method, which is mass per unit volume.

1.3 The text of this test method references notes and footnotes that provide explanatory information. These notes and footnotes (excluding those in tables) shall not be considered as requirements of this test method.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (WARNING-Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.²)

ASTM C1077-13a : Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This practice identifies and defines the duties, responsibilities, and minimum technical requirements of testing agency personnel and the minimum technical requirements for equipment utilized in testing concrete and concrete aggregates for use in construction.

1.2 This practice provides criteria for the evaluation of the capability of a testing agency to perform designated ASTM test methods on concrete and concrete aggregates. It can be used by an evaluation authority in the inspection or accreditation of a testing agency or by other parties to determine if the agency is qualified to conduct the specified tests.

Note 1-Specification E329 provides criteria for the evaluation of agencies that perform the inspection of concrete during placement.

1.3 This practice provides criteria for Inspection Bodies and Accreditation Bodies that provide services for evaluation of testing agencies in accordance with this practice.

ASTM C1029-13 : Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers the types and physical properties of spray applied rigid cellular polyurethane intended for use as thermal insulation. The operating temperatures of the surfaces to which the insulation is applied shall not be lower than −22°F (−30°C) or greater than +225°F (+107°C). For specific applications, the actual temperature limits shall be as agreed upon between the manufacturer and the purchaser.

ASTM B963-13 : Standard Test Methods for Oil Content, Oil-Impregnation Efficiency, and Interconnected Porosity of Sintered Powder Metallurgy (PM) Products Using Archimedes’ Principle

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This standard describes three related test methods that cover the measurement of physical properties of oil-impregnated powder metallurgy products.

1.1.1 Determination of the volume percent of oil contained in the material.

1.1.2 Determination of the efficiency of the oil-impregnation process.

1.1.3 Determination of the percent interconnected porosity by oil impregnation.

1.2 With the exception of the values for density and the mass used to determine density, for which the use of the gram per cubic centimetre (g/cm³) and gram (g) units is the long-standing industry practice, the values in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ASTM B962-13 : Standard Test Methods for Density of Compacted or Sintered Powder Metallurgy (PM) Products Using Archimedes’ Principle

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This standard describes a method for measuring the density of powder metallurgy products that usually have surface-connected porosity.

1.2 The density of impermeable PM materials, those materials that do not gain mass when immersed in water, may be determined using Test Method B311.

1.3 The current method is applicable to green compacts, sintered parts, and green and sintered test specimens.

1.4 With the exception of the values for density and the mass used to determine density, for which the use of the gram per cubic centimetre (g/cm³) and gram (g) units is the long-standing industry practice, the values in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ASTM B701/B701M-13 : Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors, Steel Reinforced (ACSR/SD)

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers concentric-lay-stranded self-damping aluminum conductor, steel-reinforced (ACSR/SD), and its component wires for use as overhead electrical conductors (Explanatory Notes 1 and 2).

1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. Each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification. For conductor sizes designated by AWG or kcmil, the requirements in SI units have been numerically converted from corresponding values stated or derived in inch-pound units. For conductor sizes designated by SI units only, the requirements are stated or derived in SI units.

1.2.1 For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard.

Note 1-ACSR/SD is designed to control aeolian vibration by integral damping. The conductors consist of a central core of a round steel wire or wires surrounded by two layers of trapezoidal aluminum 1350-H19 wires or two layers of trapezoidal aluminum 1350-H19 wires and one layer of round aluminum 1350-H19 wires (Fig. 1). The trapezoidal-wire layers are separated from each other and from the steel core by two small annular gaps that provide the conductors self-damping characteristics. The round aluminum wires are in tight layer contact between themselves and the underlying trapezoidal wire layer. Different strandings of the same size of conductor are identified by type, which is the approximate ratio of steel area to aluminum area, expressed in percent (Table 1 and Table 2).

FIG. 1 Illustrations of Typical ACSR/SD Strandings

Note 2-The aluminum and temper designations conform to ANSI Standard H 35.1. Aluminum 1350 corresponds to UNS A91350 in accordance with Practice E527.

ASTM B610-13 : Standard Test Method for Measuring Dimensional Changes Associated with Processing Metal Powders

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This standard covers a test method that may be used to measure the sum of the changes in dimensions that occur when a metal powder is first compacted into a test specimen and then sintered.

1.2 The dimensional change is determined by a quantitative laboratory procedure in which the arithmetic difference between the dimensions of a die cavity and the dimensions of a sintered test specimen produced from that die is calculated and expressed as a percent growth or shrinkage.

1.3 With the exception of the values for density and the mass used to determine density, for which the use of the gram per cubic centimetre (g/cm³) and gram (g) units is the long-standing industry practice, the values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ASTM B311-13 : Standard Test Method for Density of Powder Metallurgy (PM) Materials Containing Less Than Two Percent Porosity

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This test method covers the determination of density for powder metallurgy (PM) materials containing less than two percent porosity and for cemented carbides. This test method is based on the water displacement method.

Note 1-A test specimen that gains mass when immersed in water indicates the specimen contains surface-connected porosity. Unsealed surface porosity will absorb water and cause density values higher than the true value. This test method is not applicable if this problem occurs.

1.2 With the exception of the values for density and the mass used to determine density, for which the use of the gram per cubic centimeter (g/cm³) and gram (g) units is the long-standing industry practice, the values in SI units are to be regarded as standard.

ASTM D4632/D4632M-08(2013)e1 : Standard Test Method for Grab Breaking Load and Elongation of Geotextiles

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This test method is an index test which provides a procedure for determining the breaking load (grab strength) and elongation (grab elongation) of geotextiles using the grab method. This test method is not suitable for knitted fabrics and alternate test methods should be used. While useful for quality control and acceptance testing for a specific fabric structure, the results can only be used comparatively between fabrics with very similar structures, because each different fabric structure performs in a unique and characteristic manner in this test. The grab test methods does not provide all the information needed for all design applications and other test methods should be used.

1.2 Procedures for measuring the breaking load and elongation by the grab method in both the dry and wet state are included; however, testing is normally done in the dry condition unless specified otherwise in an agreement or specification.

ASTM B213-13 : Standard Test Methods for Flow Rate of Metal Powders Using the Hall Flowmeter Funnel

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This test method covers the determination of a flow rate, by the use of the Hall Flowmeter funnel of metal powders and powder mixtures. It is suitable only for those powders that will flow unaided through the Hall Flowmeter funnel.

1.2 With the exception of the values for density and the mass used to determine density, for which the use of the gram per cubic centimeter (g/cm³) and gram (g) units is the longstanding industry practice, the values in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only, and are not considered standard.

ASTM B212-13 : Standard Test Method for Apparent Density of Free-Flowing Metal Powders Using the Hall Flowmeter Funnel

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This test method describes a procedure for determining the apparent density of free-flowing metal powders, and mixed powders; and is suitable for only those powders that will flow unaided through the specified Hall Flowmeter funnel.

1.2 With the exception of the values for mass, volume, and density, for which the use of the gram and the cubic centimeter units is the long-standing industry practice, the values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ASTM A999/A999M-13 : Standard Specification for General Requirements for Alloy and Stainless Steel Pipe

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification² covers a group of general requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below.

Title of Specification	ASTM Desig- nation³

Seamless and Welded Austenitic Stainless Steel Pipes	A312/A312M
Seamless and Welded Steel Pipe for Low-Temperature Service	A333/A333M
Seamless Ferritic Alloy-Steel Pipe for High Temperature Service	A335/A335M
Electric-Fusion-Welded Austenitic Chromium-Nickel Alloy Steel Pipe for High-Temperature Service	A358/A358M
Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service	A369/A369M
Seamless Austenitic Steel Pipe for Use With High Temperature Central-Station Service	A376/A376M
Welded Large Diameter Austenitic Steel Pipe for Corrosive or High-Temperature Service	A409/A409M
Centrifugally Cast Ferritic Alloy Steel Pipe for High-Temperature Service	A426/A426M
Centrifugally Cast Austenitic Steel Pipe for High- Temperature Service	A451/A451M
Centrifugally Cast Iron-Chromium-Nickel High-Alloy Tubing for Pressure Application at High Temperatures	A608/A608M
Welded, Unannealed Austenitic Stainless Steel Tubular Products	A778
Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe	A790/A790M
Single- or Double-Welded Austenitic Stainless Steel Pipe	A813/A813M
Cold-Worked Welded Austenitic Stainless Steel Pipe	A814/A814M
Centrifugally Cast Ferritic/Austenitic Stainless Steel Pipe for Corrosive Environments	A872/A872M
Ferritic/Austenitic (Duplex) Stainless Steel Pipe Electric Fusion Welded with Addition of Filler Metal	A928/A928M
Spray-Formed Seamless Austenitic Stainless Steel Pipe	A943/A943M
Spray-Formed Seamless Ferritic/Austenitic Stainless Steel Pipe	A949/A949M
Austenitic Chromium-Nickel-Silicon Alloy Steel Seamless and Welded Pipe	A954

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units apply unless the “M” designation (SI) of the product specification is specified in the order.

Note 1-The dimensionless designator NPS (nominal pipe size) is used in this standard for such traditional terms as “nominal diameter,” “size,” “ nominal bore,” and “nominal size.”

1.4 The following precautionary statement pertains only to the test method portion, Section 22, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM A985/A985M-13 : Standard Specification for Steel Investment Castings General Requirements, for Pressure-Containing Parts

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers a group of common requirements that are mandatory for steel castings produced by the investment casting process for pressure-containing parts under each of the following ASTM Specifications:

	Title of Specification	ASTM Designation

Steel Castings, Carbon, Suitable for Fusion Welding,		A216/A216M
	for High-Temperature Service
Steel Castings, Martensitic Stainless and Alloy, for		A217/A217M
	Pressure-Containing Parts, Suitable for High-
	Temperature Service
Castings, Austenitic, Austenitic-Ferritic (Duplex),		A351/A351M
	for Pressure-Containing Parts
Steel Castings, Ferritic and Martensitic, for Pressure-		A352/A352M
	Containing Parts, Suitable for Low-Temperature
	Service
Steel Castings, Alloy, Specially Heat-Treated, for		A389/A389M
	Pressure-Containing Parts, Suitable for High-
	Temperature Service
Steel Castings Suitable for Pressure Service		A487/A487M
Castings, Iron-Nickel-Chromium and Nickel Alloys, Specially Controlled for Pressure Retaining Parts for Corrosive Service		A990
Castings, Austenitic-Ferritic (Duplex) Stainless Steel, for Pressure-Containing Parts		A995/A995M

1.2 This specification also covers a group of supplementary requirements, which may be applied to the above specifications as indicated therein. These requirements are provided for use when additional testing or inspection is desired and apply only when specified individually by the purchaser in the order.

1.3 When investment casting is ordered, the requirements of this specification shall take precedence over the individual material specification requirements.

ASTM A947M-13 : Standard Specification for Textured Stainless Steel Sheet [Metric]

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers stainless steel, textured sheets, especially for use in electronic packaging applications, for example, cabinet, rack, enclosure, and shelf constructions for telecommunication, computer, and data-processing equipment.

1.2 This specification applies to all finished flat-rolled stainless products specified by standards organizations such as International Standards Organization (ISO), American Society for Testing and Materials (ASTM), European Committee for Standardization (CEN), German Institute for Standardization (DIN), and others participating in a global standards harmonization effort.

1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

ASTM A781/A781M-13 : Standard Specification for Castings, Steel and Alloy, Common Requirements, for General Industrial Use

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers a group of requirements that are mandatory requirements of the following steel casting specifications issued by ASTM. If the product specification specifies different requirements, the product specification shall prevail.

ASTM Designation	Title of Specification
A27/A27M	Steel Castings, Carbon, for General Application
A128/A128M	Steel Castings, Austenitic Manganese
A148/A148M	Steel Castings, High Strength, for Structural Purposes
A297/A297M	Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant for General Application
A447/A447M	Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service
A494/A494M	Castings, Nickel and Nickel Alloy
A560/A560M	Castings, Chromium-Nickel Alloy
A743/A743M	Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for General Application
A744/A744M	Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe
A747/A747M	Steel Castings, Stainless, Precipitation Hardening
A890/A890M	Castings, Iron-Chromium-Nickel-Molybdenum Corrosion-Resistant, Duplex (Austenitic/Ferritic) for General Application
A915/A915M	Steel Castings, Carbon and Alloy, Chemical Requirements Similar to Standard Wrought Grades
A958	Steel Castings, Carbon and Alloy, with Tensile Requirements, Chemical Requirements Similiar to Standard Wrought Grades
A1002	Castings, Nickel-Aluminum Ordered Alloy

1.2 This specification also covers a group of supplementary requirements that may be applied to the above specifications as indicated therein. These are provided for use when additional testing or inspection is desired and apply only when specified individually by the purchaser in the order.

1.3 The requirements of the individual material specification, and this general specification shall prevail in the sequence named.

ASTM A743/A743M-13 : Standard Specification for Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for General Application

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers iron-chromium and iron-chromium-nickel alloy castings for general corrosion-resistant application. The grades covered by this specification represent types of alloy castings suitable for broad ranges of application which are intended for a wide variety of corrosion environments.

Note 1-For alloy castings for severe corrosion-resistant service, reference should be made to Specification A744/A744M. For general heat-resistant alloy castings, reference should be made to Specification A297/A297M. For nickel alloy castings for corrosion-resistant service, reference should be made to Specification A494/A494M.

1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. Inch-pound units are applicable for material ordered to Specification A743 and SI units for material ordered to Specification A743M.

ASTM A6/A6M-13 : Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This general requirements specification² covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled structural steel bars, plates, shapes, and sheet piling covered by each of the following product specifications issued by ASTM:

ASTM Designation³	Title of Specification
A36/A36M	Carbon Structural Steel
A131/A131M	Structural Steel for Ships
A242/A242M	High-Strength Low-Alloy Structural Steel
A283/A283M	Low and Intermediate Tensile Strength Carbon Steel Plates
A328/A328M	Steel Sheet Piling
A514/A514M	High-Yield Strength, Quenched and Tempered Alloy Steel Plate Suitable for Welding
A529/A529M	High-Strength Carbon-Manganese Steel of Structural Quality
A572/A572M	High-Strength Low-Alloy Columbium-Vanadium Steel
A573/A573M	Structural Carbon Steel Plates of Improved Toughness
A588/A588M	High-Strength Low-Alloy Structural Steel with 50 ksi (345 MPa) Minimum Yield Point to 4 in. [100 mm] Thick
A633/A633M	Normalized High-Strength Low-Alloy Structural Steel Plates
A656/A656M	Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability
A690/A690M	High-Strength Low-Alloy Steel H-Piles and Sheet Piling for Use in Marine Environments
A709/A709M	Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges
A710/A710M	Age-Hardening Low-Carbon Nickel-Copper-Chromium-Mo- lybdenum-Columbium Alloy Structural Steel Plates
A769/A769M	Carbon and High-Strength Electric Resistance Welded Steel Structural Shapes
A786/A786M	Rolled Steel Floor Plates
A827/A827M	Plates, Carbon Steel, for Forging and Similar Applications
A829/A829M	Plates, Alloy Steel, Structural Quality
A830/A830M	Plates, Carbon Steel, Structural Quality, Furnished to Chemical Composition Requirements
A857/A857M	Steel Sheet Piling, Cold Formed, Light Gage
A871/A871M	High-Strength Low-Alloy Structural Steel Plate With Atmospheric Corrosion Resistance
A913/A913M	High-Strength Low-Alloy Steel Shapes of Structural Quality, Produced by Quenching and Self-Tempering Process (QST)
A871/A871M	High-Strength Low-Alloy Structural Steel Plate With Atmospheric Corrosion Resistance
A945/A945M	High-Strength Low-Alloy Structural Steel Plate with Low Carbon and Restricted Sulfur for Improved Weldability, Formability, and Toughness
A950/A950M	Fusion Bonded Epoxy-Coated Structural Steel H-Piles and Sheet Piling
A992/A992M	Steel for Structural Shapes for Use in Building Framing
A1043/A1043M	Structural Steel with Low Yield to Tensile Ratio for Use in Buildings
A1066/A1066M	High-Strength Low-Alloy Structural Steel Plate Produced by Thermo-Mechanical Controlled Process (TMCP)

1.2 Annex A1 lists permitted variations in dimensions and mass (Note 1) in SI units. The values listed are not exact conversions of the values in Tables 1 to 31 inclusive but are, instead, rounded or rationalized values. Conformance to Annex A1 is mandatory when the “M” specification designation is used.

Note 1-The term “weight” is used when inch-pound units are the standard; however, under SI, the preferred term is “mass.”

1.3 Annex A2 lists the dimensions of some shape profiles.

1.4 Appendix X1 provides information on coil as a source of structural products.

1.5 Appendix X2 provides information on the variability of tensile properties in plates and structural shapes.

1.6 Appendix X3 provides information on weldability.

1.7 Appendix X4 provides information on cold bending of plates, including suggested minimum inside radii for cold bending.

1.8 This general requirements specification also covers a group of supplementary requirements that are applicable to several of the above product specifications as indicated therein. Such requirements are provided for use where additional testing or additional restrictions are required by the purchaser, and apply only where specified individually in the purchase order.

1.9 In case of any conflict in requirements, the requirements of the applicable product specification prevail over those of this general requirements specification.

1.10 Additional requirements that are specified in the purchase order and accepted by the supplier are permitted, provided that such requirements do not negate any of the requirements of this general requirements specification or the applicable product specification.

1.11 For purposes of determining conformance with this general requirements specification and the applicable product specification, values are to be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29.

1.12 The text of this general requirements specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.

1.13 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way.

1.14 This general requirements specification and the applicable product specification are expressed in both inch-pound units and SI units; however, unless the order specifies the applicable “M” specification designation (SI units), the structural product is furnished to inch-pound units.

1.15 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM A574-13 : Standard Specification for Alloy Steel Socket-Head Cap Screws

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket-head cap screws, 0.060 through 4 in. in diameter where high strength is required.

1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

Note 1-A complete metric companion to Specification A574 has been developed-A574M; therefore no metric equivalents are presented in this specification.

1.3 The following hazard caveat pertains only to the test method portions, sections 5.1, 5.6, 8, and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM A531/A531M-13 : Standard Practice for Ultrasonic Examination of Turbine-Generator Steel Retaining Rings

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This practice covers ultrasonic examination of turbine-generator retaining rings produced in accordance with Specifications A288 and A289/A289M with an inside diameter to wall thickness ratio equal to or greater than 5:1 and with wall thicknesses from 1 to 4 in. [25 to 102 mm].

1.2 Forgings may be inspected by either the contact or the immersion methods, or combinations thereof, as agreed upon between the manufacturer and the purchaser.

1.3 Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract.

1.4 This practice is expressed in inch-pound and SI units; however, unless the purchase order or contract specifies the applicable “M” specification designation (SI units), the inch-pound units shall apply. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the practice, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

ASTM A1013-00(2013)e1 : Standard Test Method for High-Frequency (10 kHz-1 MHz) Core Loss of Soft Magnetic Core Components at Controlled Temperatures Using the Voltmeter-Ammeter-Wattmeter Method

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This test method covers the equipment, procedures, and measurement of core loss of either toroidal or mated soft magnetic core components, such as soft ferrite cores, iron powder cores, and so forth, over ranges of controlled ambient temperatures typically from −20 to +120°C, frequencies from 10 kHz to 1 MHz, under sinusoidal flux conditions.

1.2 The values and equations stated in customary (cgs-emu and inch-pound) or SI units are to be regarded separately as standard. Within this test method, SI units are shown in brackets except for the sections concerning calculations where there are separate sections for the respective unit systems. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this standard.

ASTM A480/A480M-13 : Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip

Wed, 19 Jun 2013 13:30:38 -0500

1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; for example, by waiving a test requirement or by making a test requirement less stringent.

1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets, except that when A480M is specified, Annex A3 shall apply for the dimensional tolerances and not the bracketed SI values in Annex A2. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

1.4 This specification and the applicable material specifications are expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation [SI units], the material shall be furnished in inch-pound units.

ASTM A479/A479M-13a : Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification² covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction.²

Note 1-There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol 02.04.

1.3 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.

ASTM A322-13 : Standard Specification for Steel Bars, Alloy, Standard Grades

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers hot-wrought alloy steel bars. Bar applications include forging, heat treating, cold drawing, machining and many structural components (Note 1).

Note 1-A guide for the selection of steel bars is contained in Practice A400.

1.2 The bars shall be furnished in the grades specified in Table 1. Sections and sizes of bar steel available are covered in Specification A29/A29M. Hot-wrought alloy steel bars are produced in cut lengths and coils; the manufacturer should be consulted regarding sections and sizes available in coils, produced to a chemical composition.

1.3 Some applications may require superior surface quality, or special chemical restrictions, metallurgical characteristics, heat treatment, or surface finishes which the purchaser may obtain by designating one or more of the available Supplementary Requirements.

ASTM A314-13 : Standard Specification for Stainless Steel Billets and Bars for Forging

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers stainless steel billets and bars intended only for forging.

ASTM A288-91(2013) : Standard Specification for Carbon and Alloy Steel Forgings for Magnetic Retaining Rings for Turbine Generators

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers quenched and tempered carbon and alloy steel forgings for magnetic retaining rings for turbine generators.

1.2 Supplementary requirements of an optional nature are provided. These shall apply only when specified by the purchaser.

ASTM A276-13 : Standard Specification for Stainless Steel Bars and Shapes

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers hot-finished or cold-finished bars except bars for reforging (Note 1). It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels. The free-machining types (Note 2) for general corrosion resistance and high-temperature service are covered in a separate specification.

Note 1-For bars for reforging, see Specification A314.

Note 2-For free-machining stainless bars designed especially for optimum machinability, see Specification A582/A582M.

Note 3-There are standards covering high nickel, chromium, austenitic corrosion, and heat resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol. 02.04.

ASTM A262-13 : Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels

Wed, 19 Jun 2013 13:30:38 -0500

1.1 These practices cover the following five tests:

1.1.1 Practice A-Oxalic Acid Etch Test for Classification of Etch Structures of Austenitic Stainless Steels (Sections 3 to 7, inclusive),

1.1.2 Practice B-Ferric Sulfate-Sulfuric Acid Test for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels (Sections 8 to 14, inclusive),

1.1.3 Practice C-Nitric Acid Test for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels (Sections 15 to 21, inclusive),

1.1.4 Practice E-Copper-Copper Sulfate-Sulfuric Acid Test for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels (Sections 22 to 31, inclusive), and

1.1.5 Practice F-Copper-Copper Sulfate-50 % Sulfuric Acid Test for Detecting Susceptibility to Intergranular Attack in Molybdenum-Bearing Austenitic Stainless Steels (Sections 32 to 38, inclusive).

1.2 The oxalic acid etch test is a rapid method of identifying, by simple etching, those specimens of certain stainless steel grades that are essentially free of susceptibility to intergranular attack associated with chromium carbide precipitates. These specimens will have low corrosion rates in certain corrosion tests and therefore can be eliminated (screened) from testing as “acceptable.” The etch test is applicable only to those grades listed in the individual hot acid tests and classifies the specimens either as “acceptable” or as “suspect.”

1.3 The ferric sulfate-sulfuric acid test, the copper-copper sulfate-50 % sulfuric acid test, and the nitric acid test are based on weight loss determinations and, thus, provide a quantitative measure of the relative performance of specimens evaluated. In contrast, the copper-copper sulfate-16 % sulfuric acid test is based on visual examination of bend specimens and, therefore, classifies the specimens only as acceptable or nonacceptable.

Note 1-See Appendix X1 for information regarding test selection.

1.4 The values stated in SI units are to be regarded as standard. The inch-pound equivalents are in parentheses and may be approximate.

1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Specific precautionary statements are given in 5.6, 11.1.1, 11.1.9, and 35.1.)

ASTM A240/A240M-13a : Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification² covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications.

1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units.

ASTM A240/A240M-13 : Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification² covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications.

ASTM A1016/A1016M-13 : Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes

Wed, 19 Jun 2013 13:30:38 -0500

1.1 This specification covers a group of requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below.

Title of Specification	ASTM Designation^A

Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes	A209/A209M
Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes	A213/A213M
Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes	A249/A249M
Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater Tubes	A250/A250M
Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service	A268/A268M
Seamless and Welded Austenitic Stainless Steel Tubing for General Service	A269
Seamless and Welded Austenitic Stainless Steel Sanitary Tubing	A270
Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature Service	A334/A334M
Welded Austenitic Stainless Steel Feedwater Heater Tubes	A668/A668M
Austenitic Stainless Steel Tubing for Breeder Reactor Core Components	A771/A771M
Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service	A789/A789M
Welded Ferritic Stainless Steel Feedwater Heater Tubes	A803/A803M
Austenitic and Ferritic Stainless Steel Duct Tubes for Breeder Reactor Core Components	A826/A826M
High-Frequency Induction Welded, Unannealed Austenitic Steel Condenser Tubes	A851

^A These designations refer to the latest issue of the respective specifications.

1.2 In the case of conflict between a requirement of a product specification and a requirement of this general requirements specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this general requirements specification and a more stringent requirement of the purchase order, the purchase order shall prevail.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.

ASTM A484/A484M-13a : Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings

Wed, 19 Jun 2013 13:30:38 -0500

1.3 The requirements for introduction of new materials in specifications referencing this specification are given in Annex A1.

1.4 General requirements for flat-rolled stainless steel products other than bar are covered in Specification A480/A480M.

1.5 General requirements for wire products in coils are covered in Specification A555/A555M.

1.7 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units.

IPC 5703 : Cleanliness Guidelines for Printed Board Fabricators

Wed, 19 Jun 2013 08:06:17 -0500

Printed board cleanliness has historically been an unknown factor in the quality assessment of unpopulated (bare) printed boards; this has often been attributed to a lack of understanding of materials and processes. This document addresses the various printed board fabrication processes and how each may impact, directly or indirectly, the final cleanliness of packaged bare printed boards and ultimately printed board quality.

BS ISO 5129:2001+A1:2013 : Acoustics. Measurement of sound pressure levels in the interior of aircraft during flight

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
ISO 800008
IEC 60942
IEC 61183
IEC 61260
IEC 61672-1 IEC 61400-11 ISO/IEC GUIDE 98-3 GUM:1995 ISO/IEC GUIDE 99 ISO 9921-1 ISO 1683

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 26842-2:2013 : Adhesives. Test methods for the evaluation and selection of adhesivesfor indoor wood products. Resistance to delamination in severe environments

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
ISO 6238
ISO 9424
ISO 16999
ISO 9142
ISO 15605
ISO 17087
ASTM D1183
ASTM D4317
ASTM D5751
ASTM D5824

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 26842-1:2013 : Adhesives. Test methods for the evaluation and selection of adhesivesfor indoor wood products. Resistance to delamination in non-severe environments

Wed, 19 Jun 2013 07:30:02 -0500

BS ISO 26143:2013 : Space data and information transfer systems. Space link extension (SLE).Return operational control fields service

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
CCSDS 911.5-B-2
CCSDS 910.4-B-2
CCSDS 131.0-B-1
CCSDS 132 .0-B-1
CCSDS 232.0-B-1
CCSDS 732.0-B-2
CCSDS 133.0-B-1
CCSDS 301.0-B-3
ISO/IEC 8824-1:2002
CCSDS 202.0-B-3
CCSDS 913.1-B-1
CCSDS A00.0-Y-9
CCSDS 910.3-G-3
CCSDS 101.0-B-6-S
CCSDS 102.0-B-5-S
CCSDS 202.0-B-3-S
CCSDS 701.0-B-3-S
CCSDS 913.1-B-1

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 22669:2013 : Space data and information transfer systems. Space link extension (SLE) .Return-all-frames service

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
CCSDS 911.1-B-3
CCSDS 910.4-B-2
CCSDS 131.0-B-1
CCSDS 132 .0-B-1
CCSDS 732.0-B-2
CCSDS 301.0-B-3
ISO/IEC 8824-1:2002
CCSDS 913.1-B-1
CCSDS A00.0-Y-9
CCSDS 910.3-G-3
CCSDS 101.0-B-6-S
CCSDS 102.0-B-5-S
CCSDS 701.0-B-3-S
CCSDS 913.1-B-1

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 22667:2013 : Space data and information transfer systems. Communications operationprocedure-1

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
CCSDS 232.1-B-2
CCSDS 232.0-B-2
CCSDS A00.0-Y-9
CCSDS 202 .1-B-2-S
CCSDS 202.1-B-1-S

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 22664:2013 : Space data and information transfer systems. TC (telecommand) space datalink protocol

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
CCSDS 232.0-B-2
CCSDS 232.1-B-2
CCSDS 910.4-B-2
CCSDS 132 .0-B-1
CCSDS 732.0-B-2
CCSDS A00.0-Y-9
CCSDS 202.0-B-3-S
CCSDS 130.0-G-2
CCSDS 910.4-B-2
CCSDS 132.0-B-1
CCSDS 732.0-B-1
CCSDS 102.0-B-5-S

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18446:2013 : Space data and information transfer systems. Space Link Extension. Application Program Interface for the Forward Space Packet Service

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
CCSDS 916.3-M-1:2008
ISO 22664:2005
ISO 15396:2007
ISO 22672:2011
ISO 18441:2013
ISO 18440:2013
CCSDS 916.3-M-1:2008
CCSDS 232.0-B-1:2003
CCSDS 910.4-B-2:2005
CCSDS 912.3-B-1:2004
CCSDS 914.0-M-1:2008
ISO/IEC 14882:2003
ISO/IEC 8824-1:2002
CCSDS A00 .0-Y-9:2003
CCSDS 910.3-G-3:2006
CCSDS 914.1-G-1:2006
CCSDS 913 .1-B-1:2008
CCSDS 914.2-G-2:2008

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18445:2013 : Space data and information transfer systems. Space Link Extension. Application Program Interface for the Forward CLTU Service

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
CCSDS 916.1-M-1:2008
CCSDS 231.0-B-1:2003
ISO 22642:2005
CCSDS 232.0-B-1:2003
ISO 22664:2005
CCSDS 910.4-B-2:2005
ISO 15396:2007
CCSDS 912.1-B-2:2004
ISO 22671:2011
CCSDS 914.0-M-1:2008
ISO 18441:2013
CCSDS 913.1-B-1:2008
ISO 18440:2013
CCSDS 231 .0-B-1:2003
CCSDS 232.0-B-1:2003
CCSDS 910.4-B-2:2005
CCSDS 912 .1-B-2:2004
CCSDS 914.0-M-1:2008
ISO/IEC 14882:2003
ISO/IEC 8824-1:2002
CCSDS A00.0-Y-9:2003
CCSDS 912.1-R1.99c:1999
CCSDS 910 .3-G-3:2006
CCSDS 914.1-G-1:2006
CCSDS 913.1-B-1:2008
CCSDS 914 .2-G-2:2008

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18444:2013 : Space data and information transfer systems. Space Link Extension. Application Program Interface for Return Operational Control Fields Service

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
CCSDS 915.5-M-1:2008
CCSDS 910.4-B-2:2005
ISO 15396:2007
CCSDS 911.5-B-1:2004
ISO 26143:2007
CCSDS 914.0-M-1:2008
ISO 18441:2013
CCSDS 913.1-B-1:2008
ISO 18440:2013
CCSDS 910.4-B-2:2005
CCSDS 911.5-B-1:2004
CCSDS 914.0-M-1:2008
ISO/IEC 14882:2003
ISO/IEC 8824-1:2002
CCSDS A00.0-Y-9:2003
CCSDS 910.3-G-3:2006
CCSDS 913.1-B-1:2008
CCSDS 914.1-G-1:2006
CCSDS 914.2-G-2:2008

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18443:2013 : Space data and information transfer systems. Space Link Extension. Application Program Interface for Return Channel Frames Service

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
CCSDS 915.2-M-1:2008
CCSDS 910.4-B-2:2005
ISO 15396:2007
CCSDS 911.2-B-2:2004
ISO 22670:2006
CCSDS 914.0-M-1:2008
ISO 18441:2013
CCSDS 913.1-B-1:2008
ISO 18440:2013
CCSDS 910.4-B-2:2005
CCSDS 911.2-B-1:2004
CCSDS 914.0-M-1:2008
ISO/IEC 14882:2003
ISO/IEC 8824-1:2002
CCSDS A00.0-Y-9:2003
CCSDS 911.2 R1.7:1999
CCSDS 910.3-G-3:2006
CCSDS 913.1-B-1:2008
CCSDS 914.1-G-1:2006
CCSDS 914 .2-G-2:2008

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18442:2013 : Space data and information transfer systems. Space Link Extension. Application Program Interface for Return All Frames Service

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
CCSDS 915.1-M-1:2008
CCSDS 910.4-B-2:2005
ISO 15396:2007
CCSDS 911.1-B-2:2004
ISO 22669:2007
CCSDS 914.0-M-1:2008
ISO 18441:2013
CCSDS 913.1-B-1:2008
ISO 18440:2013
CCSDS A00.0-Y-9:2003
CCSDS 911.1-R1.7:1999
CCSDS 910.3-G-3:2006
CCSDS 913.1-B-1:2008
CCSDS 914.1-G-1:2006
CCSDS 914.2-G-:2008

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18441:2013 : Space data and information transfer systems. Space Link Extension. Application Program Interface for Transfer Services. Core Specification

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
ISO 11104:2011
ISO 15396:2007
ISO 22669:2007
ISO 22670:2006
ISO 26143:2007
ISO 22671:2011
ISO 22672:2011
ISO 18440:2013
ISO 18442:2013
ISO 18443:2013
ISO 18444:2013
ISO 18445:2013
ISO 18446:2013
CCSDS 914.0-M-1:2008
CCSDS 301.0-B-3:2002
CCSDS 910.3-G-3:2006
CCSDS 910.4-B-2:2005
CCSDS 911.1-B-2:2004
CCSDS 911 .2-B-1:2004
CCSDS 911.5-B-1:2004
CCSDS 912.1-B-2:2004
CCSDS 912 .3-B-1:2004
CCSDS 913.1-B-1:2008
CCSDS 915.1-M-1:2008
CCSDS 915 .2-M-1:2008
CCSDS 915.5-M-1:2008
CCSDS 916.1-M-1:2008
CCSDS 916 .3-M-1:2008
ISO/IEC 8824-1:2002
ISO/IEC 8825-1:2002
ISO/IEC 9594-2:1998
ISO/IEC 9594-8:2001
ISO/IEC 10021-3:1990
ISO/IEC 14882:2003
Federal Information Processing Standards Publication
180-1 MD: NIST, 1995
CCSDS A00.0-Y-9:2003
CCSDS 910.11-R-3:2008
CCSDS 914 .1-G-1:2006
CCSDS 914.2-G-2:2008

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18440:2013 : Space data and information transfer systems. Space Link Extension. Internet Protocol for Transfer Services

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
CCSDS 913.1-B-1:2008
CCSDS 910.4-B-2:2005
ISO 15396:2007
CCSDS 911.1-B-2:2004
ISO 22669:2007
CCSDS 911.2-B-1:2004
ISO 22670:2006
CCSDS 911.5-B-1:2004
ISO 26143:2007
CCSDS 912.1-B-2:2004
ISO 22671:2011
CCSDS 912.3-B-1:2004
ISO 22672:2011
CCSDS 301 .0-B-3:2002
ISO 11104:2011
CCSDS 913.1-B-1:2008
CCSDS 910.4-B-2:2005
CCSDS 911.1-B-2:2004
CCSDS 911.2-B-1:2004
CCSDS 911.5-B-1:2004
CCSDS 912.1-B-2:2004
CCSDS 912.3-B-1:2004
ISO/IEC 8824-1:2002
ISO/IEC 8825-1:2002
ISO/IEC 9594-8:2001
MD: NIST 1995
CCSDS 301 .0-B-3:2005
ISO/IEC 7498-1:1994
CCSDS A00.0-Y-9:2003
CCSDS 910 .3-G-3:2006
CCSDS 911.1-R1.7:1999
CCSDS 911.2-R1.7:1999
CCSDS 912 .1-R1.99h:2000
SLES-SW-API-0002-TOSGCI:2001
SLES-SW-API-0001-TOS-GCI:2000
VA: ISOC 2004
RFC 792:1981
ISO/IEC 19501:2005

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18439:2013 : Space data and information transfer systems. Space Communication CrossSupport. Service Management. Service Specification

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
CCSDS 910.11-B-1
CCSDS 910.4-B-2
CCSDS 132.0-B-1
CCSDS 133 .0-B-1
CCSDS 131.0-B-1
CCSDS 732.0-B-2
CCSDS 231.0-B-1
CCSDS 232.1-B-1
CCSDS 911.1-B-2
CCSDS 911.2-B-2
CCSDS 911.5-B-2
CCSDS 912.1-B-2
CCSDS 912.3-B-1
CCSDS 502.0-B-1
CCSDS 910.3-G-3
CCSDS 910.14-G-0

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18438:2013 : Space data and information transfer systems. Spacecraft OnboardInterface Services . Subnetwork Test Service

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
CCSDS 855.0-M-1
CCSDS 850.0-G-1
CCSDS 350.0-G-2
ISO/IEC 7498-1:1994

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18428:2013 : Space data and information transfer systems. Spacecraft Onboard Interface Services. Subnetwork Device Discovery Service

Wed, 19 Jun 2013 07:30:02 -0500

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18427:2013 : Space data and information transfer systems. Spacecraft Onboard Interface Services. Subnetwork Synchronization Service

Wed, 19 Jun 2013 07:30:02 -0500

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18426:2013 : Space data and information transfer systems. Spacecraft Onboard Interface Services. Subnetwork Memory Access Service

Wed, 19 Jun 2013 07:30:02 -0500

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 8536-12:2007+A1:2013 : Infusion equipment for medical use. Check valves

Wed, 19 Jun 2013 07:30:02 -0500

Cross References:
ISO 31-3
ISO 594-2
ISO 8536-4:2004
ISO 8871-1
ISO 8871-2
ISO 10993-1
ISO 15223-1

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18424:2013 : Space data and information transfer systems. XML Telemetric and CommandExchange (XTCE)

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
CCSDS 660.0-B-1
CCSDS 301.0-B-2
CCSDS 102.0-B-4
CCSDS 203 .0-B-1
ECSS-E-70-41
S2K-MCS-ICD-0001-TOS-GCI
ESA PSS-07-101
CCSDS 301.0-B-2
S2K-MCS-SUM-0019-TOS-GCI
IRIG-106

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18423:2013 : Space data and information transfer systems. Pseudo-Noise (PN) RangingSystems

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
CCSDS 414.1-B-1
CCSDS 414.0-G-0

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18382:2013 : Space data and information transfer systems. Spacecraft onboardinterface services . RFID-based inventory management systems

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
CCSDS 881.0-M-1, May 2012
ETSI EN 300 220-1
ETSI EN 302 208-1

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18381:2013 : Space data and information transfer systems. Lossless multispectral and hyperspectral image compression

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
CCSDS 123.0-B-1:2012
CCSDS 121.0-B-2:2012
ISO 15887:2013
CCSDS 133.0-B-1:2003
ISO 22646:2005
CCSDS 727-0-B-4:2007
ISO 17355:2007
CCSDS 732.0-B-2:2006
ISO 22666:2006
CCSDS 123.0-B-1:2012
CCSDS 121.0-B-2:2012
CCSDS 120.2-G-0
CCSDS 133.0-B-1:2003
CCSDS 727.0-B-4:2007
CCSDS 732.0-B-2:2006

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18202:2013 : Space data and information transfer systems. Mission operations messageabstraction layer

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
CCSDS 521.0-B-1
CCSDS 520.1-M-1
CCSDS 520.0-G-3

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18201:2013 : Space data and information transfer systems. Mission operationsreference model

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
CCSDS 520.1-M-1
CCSDS 911.1-B-3
CCSDS 912.1-B-2
CCSDS 727 .0-B-4
CCSDS 735.1-B-1
CCSDS 133.0-B-1
CCSDS 502.0-B-2
CCSDS 504.0-B-1
CCSDS 851.0-M-1
CCSDS 520.0-G-3
CCSDS 911.1-B-3
CCSDS 912.1-B-2
CCSDS 727.0-B-4
CCSDS 735.1-B-1
CCSDS 133.0-B-1
CCSDS 502.0-B-2
CCSDS 503.0-B-1
CCSDS 504.0-B-1
CCSDS 851 .0-M-1

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 17949:2013 : Impact test procedures for road vehicles. Seating and positioningprocedures for anthropomorphic test devices. Procedure for the WorldSID5Oth percentile male side-impact dummy in front outboard seatingpositions

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
ISO 15830-1
ISO 15830-2
ISO 15830-3
ISO 15830-4
SAE J 826

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 17854:2013 : Space data and information transfer systems. Flexible advanced codingand modulation scheme for high rate telemetry applications

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
CCSDS 131.2-B-1
CCSDS 131.0-B-2
CCSDS 132.0-B-1
CCSDS 732 .0-B-2
ISO/IEC 7498-1

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 17807:2013 : Space data and information transfer systems. Asynchronous messageservice

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
ISO/IEC 7498-1:1994
ISO/IEC 10731:1994

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 16236:2013 : Crop protection equipment. Test method for the determination of drainable volume and its concentration

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
ISO 13440
ISO 22368-1
ISO 22368-2
ISO 22368-3

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 15887:2013 : Space data and information transfer systems. Lossless data compression

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
CCSDS 121.0-B-2:2012
CCSDS 131.0-B-2:2012
ISO 22641:2012
CCSDS 133.0-B-1:2003
ISO 22646:2005
CCSDS 123.0-B-1:2012
ISO 18281:2013
CCSDS 121.0-B-1:1997
CCSDS 121.0-B-2:2012
CCSDS 131 .0-B-2:2011
CCSDS 133.0-B-1.:2003
CCSDS 123.0-B-1:2012
CCSDS A02 .1-Y-3:2011
CCSDS 120.0-G-2:2006

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 18425:2013 : Space data and information transfer systems. Spacecraft Onboard Interface Services. Subnetwork Packet Service

Wed, 19 Jun 2013 07:30:01 -0500

All current amendments available at time of purchase are included with the purchase of this document.

BS ISO 10008:2013 : Quality management. Customer satisfaction. Guidelines for business-to-consumer electronic commerce transactions

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
ISO 9000
ISO 9001
ISO 9004
ISO 9241
ISO 9241-151
ISO 10001:2007
ISO 10002
ISO 10003
ISO 10004
ISO/TR 10013
ISO 10015
ISO 19011
ISO/IEC 27001
ISO/IEC 27002
ISO/IEC Guide 76:2008

All current amendments available at time of purchase are included with the purchase of this document.

BS IEC 62646:2012 : Nuclear power plants. Control rooms. Computer based procedures

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
IEC 60671
IEC 60880
IEC 60964:2009
IEC 60965:2009
IEC 61513
IEC 61772
IEC 61839
IEC 62138
IEC 62241:2004
ISO 11064
IEC 61226
IEC 62645

Incorporates the following:
Corrigendum, June 2013

BS EN ISO 9233-1:2013 : Cheese, cheese rind and processed cheese. Determination of natamycin content. Molecular absorption spectrometric method for cheese rind

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
ISO 707
IDF 50
ISO 5725:1986

Incorporates the following:
Amendment, November 2012. Amends and replaces BS ISO 9233-1:2007 Corrigendum, June 2013

BS EN ISO 8611-2:2012 : Pallets for materials handling. Flat pallets. Performance requirements and selection of tests

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
ISO 445
ISO 8611-1
ISO 8611-3
EN 1087-1
EN 13183-2

Incorporates the following:
Corrigendum, June 2013

BS EN ISO 80000-9:2013+A1:2011 : Quantities and units. Physical chemistry and molecular physics

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
ISO 80000-3:2006
ISO 80000-4:2006
ISO 80000-5:2007
IEC 80000-6:2008
ISO 80000-1:2009
ISO 80000-10:2009

Incorporates the following:
Amendment, August 2011. Amends and replaces BS ISO 80000-9:2009. Corrigendum, June 2013

BS EN ISO 80000-4:2013 : Quantities and units. Mechanics

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
ISO 31-4:1992
ISO 31-11:1992
ISO 80000-3:2006

Incorporates the following:
Corrigendum, June 2013

BS EN ISO 80000-3:2013 : Quantities and units. Space and time

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
ISO 8601:2004

Incorporates the following:
Corrigendum, June 2013

BS ISO 1004-2:2013 : Information processing. Magnetic ink character recognition. Print specifications for CMC7

Wed, 19 Jun 2013 07:30:01 -0500

Cross References:
ISO 1004-1:2013

All current amendments available at time of purchase are included with the purchase of this document.

BS EN ISO 80000-11:2013 : Quantities and units. Characteristic numbers

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
ISO 80000-3:2006
ISO 80000-4:2006
ISO 80000-5:2007
IEC 80000-6:2008
ISO 80000-8:2007
ISO 80000-9

Incorporates the following:
Corrigendum, June 2013

BS EN ISO 80000-12:2013 : Quantities and units. Solid state physics

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
ISO 80000-3:2006
ISO 80000-4:2006
ISO 80000-5:2007
IEC 80000-6:2008
ISO 80000-8:2007
ISO 80000-9:2009
ISO 80000-10
CODATA 2006

Incorporates the following:
Corrigendum, June 2013

BS EN ISO 23611-5:2013 : Soil quality. Sampling of soil invertebrates. Sampling and extraction of soil macro-invertebrates

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
ISO 10390
ISO 10694
ISO 11274
ISO 11277
ISO 11461
ISO 11465

Incorporates the following:
Corrigendum, June 2013

BS EN ISO 22155:2013 : Soil quality. Gas chromatographic determination of volatile aromatic and halogenated hydrocarbons and selected ethers. Static headspace method

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
ISO 10381-1:2002
ISO 10381-2
ISO 11465
ISO 15680
ISO 18512
ISO 22892
ISO 5725-5
ISO 10301:1997
ISO 14507:2003
ISO 15009:2002

Incorporates the following:
Corrigendum, June 2013

BS EN ISO 13088:2012 : Gas cylinders. Acetylene cylinder bundles. Filling conditions and filling inspection

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
ISO 11372
ISO 3807
ISO 80000-4

Incorporates the following:
Corrigendum, June 2013

BS EN ISO 12779:2013 : Lactose. Determination of water content. Karl Fischer method

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
ISO 707
IDF 50
ISO 5725-1
ISO 5725-2

Incorporates the following:
Corrigendum, June 2013

BS EN ISO 11664-3:2013 : Colorimetry. CIE tristimulus values

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
CIE DS 017.2/E:2009
ISO 11664-1:2007(E)/CIE S 014-1/E:2006
ISO 11664-2:2007(E)/CIE S 014-2/E:2006
ISO 23539:2005(E)/CIE S 010/E:2004
ASTM E308-08
ASTM E2022-08
ASTM E2729-09
CIE 15:2004
CIE 165:2005
CIE 167:2005

Incorporates the following:
Corrigendum, June 2013

BS EN ISO 11269-2:2013 : Soil quality. Determination of the effects of pollutants on soil flora. Effects of contaminated soil on the emergence and early growth of higher plants

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
ISO 10381-6
ISO 10390
ISO 10694
ISO 11260
ISO 11268-1
ISO 11268-2
ISO 11277
ISO 11465
ISO 22030
ISO 11074
ISO 11259
ISO 11274
ISO 15176:2002

Incorporates the following:
Corrigendum, June 2013

BS EN 927-1:2013 : Paints and varnishes. Coating materials and coating systems for exterior wood. Classification and selection

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
EN ISO 2808:2007
ISO 2808:2007
EN ISO 2813
EN 351-1:2007
EN 927-3:2012
EN 927-5:2006
EN ISO 4618:2006
ISO 4618:2006

All current amendments available at time of purchase are included with the purchase of this document.

BS EN 71-5:2013 : Safety of toys. Chemical toys (sets) other than experimental sets

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
EN ISO 3104
ISO 3104
EN ISO 3219
ISO 3219
EN ISO 3696
ISO 3696
EN ISO 22854
ISO 22854 EN 71-4:2013 EN ISO 8317 ISO 8317 EN ISO 11885 ISO 11885 ISO 2561 Regulation (EC) No 1272/2008 67/548/EEC 1999/45/EC Regulation (EC) No 1907/2006 67/548/EEC 1999/45/EC Regulation (EC) No 1907/2006 Regulation (EC) No 1333/2008 76/768/EEC Commission Regulation (EU) No 10/2011 2009/48/EC

All current amendments available at time of purchase are included with the purchase of this document.

BS EN 71-3:2013 : Safety of toys. Migration of certain elements

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
EN 71-1:2011
EN ISO 3696
ISO 3696
2009/48/EC
2012/7/EU

All current amendments available at time of purchase are included with the purchase of this document.

BS EN ISO 80000-10:2013 : Quantities and units. Atomic and nuclear physics

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
ISO 80000-3:2006
ISO 80000-4:2006
ISO 80000-5:2007
IEC 80000-6:2008
ISO 80000-7:2008
ISO 80000-9:2009
ISO 80000-1
ISO 80000-2:2009
IEC 60050-393:2003
ICRP 103:2007

Incorporates the following:
Corrigendum, June 2013

BS EN 71-12:2013 : Safety of toys. N-Nitrosamines and N-nitrosatable substances

Wed, 19 Jun 2013 07:30:00 -0500

Cross References:
EN ISO 3696
ISO 3696
2009/48/EC
prEN 71-7:2012
EN 12868:1999
ISO 10130
ISO 15819
ISO 29941
93/11/EEC

All current amendments available at time of purchase are included with the purchase of this document.

BS EN 62227:2008+A1:2013 : Multimedia home server systems. Digital rights permission code

Wed, 19 Jun 2013 07:29:59 -0500

Cross References:
ISO 3166-1:2006
EN ISO 3166-1:2006

Incorporates the following:
Amendment, June 2013. Amends and replaces BS EN 62227:2008

BS EN 61347-1:2008+A2:2013 : Lamp controlgear. General and safety requirements

Wed, 19 Jun 2013 07:29:59 -0500

Cross References:
IEC 60216
IEC 60317-0-1:2008
IEC 60598-1:2008
IEC 60598-2
IEC 60664-1:2007
IEC 60065:2001
IEC 60085:1987
IEC 60691:2002
IEC 60884-2-4
IEC 60906-3
IEC 60950-1
IEC 61558-1:2005
IEC 61558-2-6:2006
IEC 615582-16:2009
IEC 60081
IEC 60317-0-1:1997
IEC 60317-0-1:1997/AMD 1:1999
IEC 60317-0-1:1997/AMD 2:2005
IEC 60384-14
IEC 60417-DB
IEC 60529:1989
IEC 60529:1989/AMD 1:1999
IEC 60598-1:2003
IEC 60664-3
IEC 60691:2002
IEC 60695-2-10
IEC 60695-11-5
IEC 60730-2-3
IEC 60901
IEC 60921:2004
IEC 60923:2005
IEC 60929:2006
IEC 60990:1999
IEC 61189-2
IEC 61249-2
IEC 61347-2
IEC 61347-2-8
IEC 61347-2-9:2000
IEC 61347-2-9:2000/AMD 1:2003
IEC 61347-2-9:2000/AMD 2:2006
ISO 4046-4:2002
EN 60081:1998
EN 60317-0-1:1998
EN 60317-0-1:1998/A1:2000
EN 60317-0-1:1998/A2:2005
EN 60384-14
EN 60529:1991
EN 60529:1991/Corrigendum:1993
EN 60529:1991/A1:2000
EN 60598-1:2004
EN 60598-1:2004/Corrigendum:2007
EN 60664-3:2003
EN 60691:2003
EN 60695-2-10:2001
EN 60695-11-5:2005
EN 60730-2-3:2007
EN 60901:1996
EN 60921:2004
EN 60923:2005
EN 60929:2006
EN 60929:2006/Corrigendum:2006
EN 60990:1999
EN 61189-2:2006
EN 61249-2
EN 61347-2
EN 61347-2-8:2001
EN 61347-2-8:2001/Corrigendum:2003
EN 61347-2-9:2001
EN 61347-2-9:2001/Corrigendum:2003
EN 61347-2-9:2001/A1:2003
EN 61347-2-9:2001/A2:2006
IEC 60065:2001
IEC 60065:2001/AMD 1:2005
EN 60065:2002
EN 60065:2002/A1:2006
IEC 60112:2003
EN 60112:2003
IEC 60155:1993
EN 60155:1995
IEC 60216-1:2001
EN 60216-1:2001
IEC 60479
IEC 60598
EN 60598
IEC 60664-1:1992
IEC 60664-1:1992/AMD 1:2000
IEC 60664-1:1992/AMD 2:2002
EN 60664-1:2003
IEC 60664-4:2005
EN 60664-4:2006
IEC 60664-5:2003
EN 60664-5:2003
IEC 60925:1989
IEC 60925:1989/AMD 1:1996
IEC 60925:1989/AMD 2:2001
EN 60925:1991
EN 60925:1991/A1:1996
EN 60925:1991/A2:2001
IEC 60927:1996
IEC 60927:1996/AMD 1:1999
IEC 60927:1996/AMD 2:2004
EN 60927:1996
EN 60927:1996/A1:1999
EN 60927:1996/A2:2004
IEC 61047:2004
EN 61047:2004
IEC 61347-2-1:2000
IEC 61347-2-1:2000/AMD 1:2005
EN 61347-2-1:2001
EN 61347-2-1:2001/A1:2006
IEC 61347-2-2:2000
IEC 61347-2-2:2000/AMD 1:2005
IEC 61347-2-2:2000/AMD 2:2006
EN 61347-2-2:2001
EN 61347-2-2:2001/A1:2006
EN 61347-2-2:2001/A2:2006
IEC 62384
EN 62384:2006
IEEE 101:1987
IEC/TR 60083:2009
IEC 60364-4-41:2001
IEC 60449:1973
IEC 61347-2-1
IEC 61347-2-2:2011

Incorporates the following:
Amendment, July 2011. Amends and replaces BS EN 61347-1:2008 which remains current. Amendment, June 2013. Amends and replaces BS EN 61347-1:2008+A1:2011 whih remains current

BS EN 61195:1999+A1:2013 : Double-capped fluorescent lamps. Safety specifications

Wed, 19 Jun 2013 07:29:59 -0500

For lamps for general lighting purposes of all groups having Fa6, Fa8, G5, G13 and R17d caps.

Cross References:
IEC 60598-1
IEC 60061-1:1969
IEC 60061-2:1969
IEC 60061-3:1969
IEC 60081:1997
IEC 60410:1973
IEC 60695-2-1/0:1994
IEC 60921:1988 EN 60061-1:1993 EN 60061-2:1993 EN 60061-3:1993 EN 60081:1998 EN 60695-2-1/0:1996 EN 60921:1991

Incorporates the following:
AMD 14352 published 15 April 2003
AMD 14352 is a Corrigendum. Amendment, June 2013. Amends and replaces BS EN 61195:2000

BS EN 62271-110:2012 : High-voltage switchgear and controlgear. Inductive load switching

Wed, 19 Jun 2013 07:29:59 -0500

Cross References:
IEC 62271-100:2008
EN 62271-100 2009
IEC 62271-106
IEC 62271-306

All current amendments available at time of purchase are included with the purchase of this document.

BS EN 15037-4:2010+A1:2013 : Precast concrete products. Beam-and-block floor systems. Expanded polystyrene blocks

Wed, 19 Jun 2013 07:29:58 -0500

Cross References:
EN 826
EN 1365-2
EN 12390-4:2000
EN 12667
EN 13163:2008
EN 13369:2004
EN 15037-1:2008
EN 13501-1
EN ISO 10211
ISO 10211:2007
EN ISO 11925-2
ISO 11925-2
EN 206-1
EN 1990
EN 1992-1-2
ENV 13670-1
EN ISO 6946
ISO 6946:2007
EN ISO 10077-2
ISO 10077-2:2003
EN ISO 10456
ISO 10456:2007
EN 1992-1-1
89/106/EEC
93/68/EEC

Incorporates the following:
Amendment, June 2013. Amends and replaces BS EN 15037-4:2010

BS EN 16337:2013 : Hardware for furniture. Strength and loading capacity of shelf supports

Wed, 19 Jun 2013 07:29:58 -0500

Cross References:
EN 320
EN 323
EN 14322
EN ISO 6270-2
ISO 6270-2
ISO 7619-2
ISO 16269-6:2005

All current amendments available at time of purchase are included with the purchase of this document.

BS EN 14141:2013 : Valves for natural gas transportation in pipelines. Performance requirements and tests

Wed, 19 Jun 2013 07:29:58 -0500

Cross References:
EN 19
EN 549
EN 558
EN 571-1
EN 682
EN 736-1:1995
EN 736-2:1997
EN 736-3:2008
EN 1369:2012
EN 1371-1:2011
EN 1435:1997
EN 1503-1
EN 1503-2
EN 1515-1
EN 1515-2
EN 1594
EN 10204:2004
EN 10228-1:1999
EN 10228-2:1998
EN 10228-3:1998
EN 10228-4
EN 12266-1:2012
EN 12516-1
EN 12516-2
EN 12516-3
EN 12517-1:2006
EN 12627:1999
EN 12681
EN 12982
EN 13942:2009
ISO 14313:2007
EN ISO 148-1
ISO 148-1
EN ISO 5210
ISO 5210
EN ISO 5211
ISO 5211
EN ISO 9712:2012
ISO 9712:2012
EN ISO 10497
ISO 10497
EN ISO 11666:2010
ISO 11666:2010
EN ISO 17637
ISO 17637
EN ISO 17638
ISO 17638
EN ISO 17640:2010
ISO 17640:2010
EN ISO 23277:2009
ISO 23277:2006
EN ISO 23278:2009
ISO 23278:2006
MSS-SP-55-2006
ASME B16.34-2004
Norsok standard M-710

All current amendments available at time of purchase are included with the purchase of this document.

BS EN 13776:2013 : LPG equipment and accessories. Filling and discharge procedures for LPGroad tankers

Wed, 19 Jun 2013 07:29:57 -0500

Cross References:
EN 12252
EN 12493:2008+A1:2012
EN ISO 14021
ISO 14021
EN ISO 14024
ISO 14024
EN ISO 14025
ISO 14025

All current amendments available at time of purchase are included with the purchase of this document.

BS EN 1304:2013 : Clay roofing tiles and fittings. Product definitions and specifications

Wed, 19 Jun 2013 07:29:57 -0500

Cross References:
EN 538
EN 539-1:2005
EN 539-2:2013
EN 1024
EN 13501-1
EN 13501-5
2000/553/EC
1996/603/EC
89/106/EEC
EN ISO 9001
ISO 9001

All current amendments available at time of purchase are included with the purchase of this document.

BS EN 13603:2013 : Copper and copper alloys. Test methods for assessing protective tin coatings on drawn round copper wire for electrical purposes

Wed, 19 Jun 2013 07:29:57 -0500

Cross References:
EN 610
ISO 2177
ASTM B33-10
EN 13602

All current amendments available at time of purchase are included with the purchase of this document.

BS EN 12316-2:2013 : Flexible sheets for waterproofing. Determination of peel resistance of joints. Plastic and rubber sheets for roof waterproofing

Wed, 19 Jun 2013 07:29:57 -0500

Cross References:
EN ISO 7500-1
EN 13416

All current amendments available at time of purchase are included with the purchase of this document.

BS PD ISO/TS 16976-8:2013 : Respiratory protective devices. Human factors. Ergonomic factors

Wed, 19 Jun 2013 07:29:56 -0500

Cross References:
ISO 16972
ISO 7731
ISO 9886
ISO 9921
ISO 10551
ISO 12894
ISO 15537
ISO 16900-7
ISO 16900-11
ISO/TS 16976-1
ISO/TS 16976-2
ISO/TS 16976-3
ISO/TS 16976-5
ISO/TS 16976-7
ISO 17420-1
ISO 17420-2
EN 166
EN 457
ANSI Z 87.1
BS 8469
16900-14

All current amendments available at time of purchase are included with the purchase of this document.

BS PD ISO/TR 13097:2013 : Guidelines for the characterization of dispersion stability

Wed, 19 Jun 2013 07:29:56 -0500

Cross References:
ISO 14887:2000
ISO 26824
ISO 14644-5:2004
ISO/TS 27687:2008
ISO 10934-1:2002
ISO 8780-1:1990
ISO 8781
EN 13900
ASTM D140112
ASTM D179193(2008)
ASTM D233701(2010)
ASTM D334290(2012)
ASTM D370789(2010)
ASTM D370989(2010)
ASTM D371699(2008)
ASTM D693010
ASTM D 706106
ASTM D711209
ASTM D714905(2011)e1
ASTM F110509

All current amendments available at time of purchase are included with the purchase of this document.

BS PD ISO/IEC TS 13249-7:2013 : Information technology. Database languages. SQL multimedia andapplication packages. History

Wed, 19 Jun 2013 07:29:56 -0500

Cross References:
ISO/IEC 9075-1:2008
ISO/IEC 9075-2:2008
ISO/IEC 9075-4:2008
ISO/IEC 9075-11:2008
ISO/IEC 13249-1:2007
ISO/IEC 9075-3:2008
ISO/IEC 9075-9:2008
ISO/IEC 9075-10:2008
ISO/IEC 9075-13:2008
ISO/IEC 9075-14:2008

All current amendments available at time of purchase are included with the purchase of this document.

BS PD IEC/TR 62655:2013 : Tutorial and application guide for high-voltage fuses

Wed, 19 Jun 2013 07:29:56 -0500

Cross References:
IEC 60038
IEC 60071-1
IEC 60076-1
IEC 60076-7
IEC 60076-12
IEC 60282-1:2009
IEC 60282-2:2008
IEC 60549
IEC 60644
IEC/TR 60890:1987
IEC 60909-0
IEC 62271-100:2012
IEC 62271-102
IEC 62271-103
IEC 62271-105:2012
IEC 62271-106
IEC 62271-107
AS1033.1
IEEE Std 18
IEEE Std 141
IEEE Std 399
IEEE Std C37.41
IEEE C37.42
IEEE C37.46
IEEE Std C37.47
IEEE C37.48
IEEE Std C37.48.1:2011
IEEE Std C37.99

All current amendments available at time of purchase are included with the purchase of this document.

BS EN 12311-2:2013 : Flexible sheets for waterproofing. Determination of tensile properties. Plastic and rubber sheets for roof waterproofing

Wed, 19 Jun 2013 07:29:56 -0500

Cross References:
EN 1849-2
EN 13416
EN ISO 7500-1
ISO 7500-1
EN 1548
EN 1847
ISO/IEC Guide 43-1
ISO 13528

All current amendments available at time of purchase are included with the purchase of this document.

BS PD CLC/TS 62441:2012 : Safeguards against accidentally caused candle flame ignition foraudio/video, communication and information technology equipment

Wed, 19 Jun 2013 07:29:56 -0500

Cross References:
IEC 60695-11-5
IEC 60695-11-10
IEC 60695-11-20
EN 60695-11-5
EN 60695-11-10
EN 60695-11-20
IEC 60417
ISO 3864

All current amendments available at time of purchase are included with the purchase of this document.

BS PAS 7:2013 : Fire risk management system. Specification

Wed, 19 Jun 2013 07:29:55 -0500

All current amendments available at time of purchase are included with the purchase of this document.

BS CWA 16642:2013 : Health care services. Quality criteria for health checks

Wed, 19 Jun 2013 07:29:55 -0500

Cross References:
2003/878/EC
EN ISO 9001:2008
ISO 9001
EN 15224:2012

All current amendments available at time of purchase are included with the purchase of this document.

BS BIP 2225:2013 : Raising the Standard for Collaboration. Harnessing the benefits of BS 11000: Collaborative Business Relationships

Wed, 19 Jun 2013 07:29:55 -0500

All current amendments available at time of purchase are included with the purchase of this document.

BS PAS 402:2013 : Waste resource management. Specification for performance reporting

Wed, 19 Jun 2013 07:29:55 -0500

All current amendments available at time of purchase are included with the purchase of this document.

API RP 17H : Recommended Practice for Remotely Operated Vehicle (ROV) Interfaces on Subsea Production Systems (Identical to ISO 13628-8: 2002), Second Edition

Tue, 18 Jun 2013 12:40:43 -0500

This document provides recommendations for development and design of remotely operated subsea tools and interfaces on subsea production systems in order to maximize the potential of standardizing equipment and design principles.

This document does not cover manned intervention, internal wellbore intervention, internal flowline inspection, tree running, and tree running equipment. However, all the related subsea remotely operated vehicle/remotely operated tool (ROV/ROT) interfaces are covered by this standard. It is applicable to the selection, design, and operation of ROTs and ROVs including ROV tooling, hereafter defined in a common term as subsea intervention systems.

NOTE This document was written to include the information from API 17M, 1st Edition (2004). With the release of API 17H, 2nd Edition (2013), API 17M is withdrawn.

CAN/CGSB 4.175-2013 Part/Partie 7 ISO 2424:2007, IDT : Revetements de sol textiles - Vocabulaire

Tue, 18 Jun 2013 11:52:49 -0500

CAN/CGSB 4.175-2013 Part/Partie 7 ISO 2424:2007, IDT : Textile Floor Coverings - Vocabulary

Tue, 18 Jun 2013 11:40:05 -0500

CMR International 2013 Pharmaceutical R&D Factbook

Tue, 18 Jun 2013 11:16:00 -0500

The CMR International 2013 Pharmaceutical R & D Factbook is the definitive up-to-date business-planning tool for decision-makers in R & D, corporate finance, business strategy, marketing planning and corporate communications.

This "rich-data enterprise PowerPoint" contains robust charts, tables, and graphs - all of which are extractable into other applications, and most of which contain all the raw data behind the graphics. Click here for more information (PDF). When you download the PowerPoint, simply drag-and-drop any graphic into any other application, or simply double-click any graphic and see the actual raw data behind the scenes. This is an incredibly powerful set of visuals and data that you will not find anywhere else.

The rich-data enterprise PowerPoint is accessible to unlimited users within your organization.

This essential reference work can help you to:

gain an in-depth understanding of industry dynamics and trends
determine how your organization performs against the market as a whole
gauge your productivity relative to your competitors
recognize the key differences between individual therapeutic areas
appreciate the consequences of adopting different R & D strategies
set internal performance targets that will motivate and challenge your businesses

Each finding is presented in a clear, easily-understood chart, accompanied by a succinct commentary highlighting the key message, and an explanation of the methodology used and the definitions applied.

CAN/CGSB 4.2 N0. 52.2-2013 (ISO 105-E03:2010, MOD) : Methodes pour epreuves textiles - Textiles - Essais de solidite des coloris - Partie E03: Solidite des coloris a l'eau chloree (eau de piscine)

Tue, 18 Jun 2013 10:48:14 -0500

CAN/CGSB 4.2 N0. 52.2-2013 (ISO 105-E03:2010, MOD) : Textile Test Methods - Textiles - Tests for Colourfastness - Part E03: Colourfastness to Chlorinated Water (Swimming-Pool Water)

Tue, 18 Jun 2013 10:05:50 -0500

CAN/CGSB 4.2 NO. 48-2013 (ISO 137:1975, MOD) : Textile Test Methods - Wool - Determination of Fibre Diameter - Projection Microscope Method

Tue, 18 Jun 2013 09:34:16 -0500

CAN/CGSB 4.2 NO. 48-2013 (ISO 137:1975, MOD) : Methodes pour epreuves textiles - Laine - Determination du diametre des fibres - Methode du microscope a projection

Tue, 18 Jun 2013 09:23:57 -0500

CAN/CGSB 4.2 NO. 6-2013 (ISO 7211-2:1984, MOD) : Methodes pour epreuves textiles - Textiles - Tissus - Construction - Methodes d'analyse - Partie 2: Determination du nombre de fils par unite de longueur

Tue, 18 Jun 2013 09:16:28 -0500

CAN/CGSB 4.2 NO. 6-2013 (ISO 7211-2:1984, MOD) : Textile Test Methods - Textiles - Woven Fabrics - Construction - Methods of Analysis - Part 2: Determination of Number of Threads per Unit Length

Tue, 18 Jun 2013 08:38:14 -0500

ISO/TS 17200:2013 : Nanotechnology - Nanoparticles in powder form - Characteristics and measurements

Tue, 18 Jun 2013 08:27:03 -0500

ISO/TS 17200:2013 lists fundamental characteristics which are commonly determined for nanoparticles in powder form. ISO/TS 17200:2013 prescribes specific measurement methods for each of these characteristics.

ISO/TS 14067:2013 : Greenhouse gases - Carbon footprint of products - Requirements and guidelines for quantification and communication

Tue, 18 Jun 2013 08:27:03 -0500

ISO/TS 14067:2013 specifies principles, requirements and guidelines for the quantification and communication of the carbon footprint of a product (CFP), based on International Standards on life cycle assessment (ISO 14040 and ISO 14044) for quantification and on environmental labels and declarations (ISO 14020, ISO 14024 and ISO 14025) for communication.

Requirements and guidelines for the quantification and communication of a partial carbon footprint of a product (partial CFP) are also provided.

ISO/TS 14067:2013 is applicable to CFP studies and different options for CFP communication based on the results of such studies.

Where the results of a CFP study are reported according to ISO/TS 14067:2013, procedures are provided to support both transparency and credibility and also to allow for informed choices.

ISO/TS 14067:2013 also provides for the development of CFP-product category rules (CFP-PCR), or the adoption of product category rules (PCR) that have been developed in accordance with ISO 14025 and that are consistent with ISO/TS 14067:2013.

ISO/TS 14067:2013 addresses only one impact category: climate change.

Offsetting is outside of the scope of ISO/TS 14067:2013.

ISO/TS 16976-8:2013 : Respiratory protective devices - Human factors - Part 8: Ergonomic factors

Tue, 18 Jun 2013 08:27:03 -0500

ISO/TS 16976-8:2013 gives guidance on the generic ergonomic factors for the preparation of standards for performance requirements, testing and use of respiratory protective devices (RPD).

It specifies principles relating to:

the biomechanical interaction between RPD and the human body;

the interaction between RPD and the human senses: vision, hearing, smell, taste and skin contact.

ISO/IEC 29182-1:2013 : Information technology - Sensor networks: Sensor Network Reference Architecture (SNRA) - Part 1: General overview and requirements

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 29182-1:2013 provides a general overview of the characteristics of a sensor network and the organization of the entities that comprise such a network. It also describes the general requirements that are identified for sensor networks.

ISO/IEC 24787:2010/Cor1:2013 : Corrigendum

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 24769-2:2013 : Information technology - Real-time locating systems (RTLS) device conformance test methods - Part 2: Test methods for air interface communication at 2,4 GHz

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 24769-2:2013 defines the test methods for determining the conformance of 2,4 GHz real-time locating system (RTLS) tags with the specifications given in the corresponding subclauses of ISO/IEC 24730-2, but does not apply to the testing of conformity with regulatory or similar requirements.

The test methods require only that the mandatory functions, and any optional functions which are implemented, be verified. This may in appropriate circumstances be supplemented by further, application-specific functionality criteria that are not available to the general case.

The RTLS tag conformance parameters included in ISO/IEC 24769-2:2013 include the mandatory direct sequence spread spectrum (DSSS) 2,4 GHz radio frequency beacon. It also includes the optional on-off keyed, frequency shift keyed (OOK/FSK) short-range radio frequency link and the optional magnetic air interface.

Unless otherwise specified, the tests in ISO/IEC 24769-2:2013 apply exclusively to RTLS tags defined in ISO/IEC 24730-2.

ISO/IEC 23009-1:2012/Cor1:2013 : Corrigendum

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 23005-5:2013 : Information technology - Media context and control - Part 5: Data formats for interaction devices

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 23005-5:2013 specifies syntax and semantics of the data formats for interaction devices, i.e. Device Commands and Sensed Information, required for providing interoperability in controlling interaction devices and in sensing information from interaction devices in real as well as virtual worlds.

ISO/IEC 23002-1:2006/Amd1:2008/Cor1:2013 : Corrigendum

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 19794-5:2005/Cor3:2013 : Corrigendum

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 19794-4:2011/Amd1:2013 : - Amendment 1: Conformance testing methodology and clarification of defects

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 18180:2013 : Information technology - Specification for the Extensible Configuration Checklist Description Format (XCCDF) Version 1.2

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 18180:2013 specifies the data model and Extensible Markup Language (XML) representation for the Extensible Configuration Checklist Description Format (XCCDF) Version 1.2. An XCCDF document is a structured collection of security configuration rules for some set of target systems. The XCCDF specification is designed to support information interchange, document generation, organizational and situational tailoring, automated compliance testing, and scoring. ISO/IEC 18180:2013 also defines a data model and format for storing results of security guidance or checklist testing. The intent of XCCDF is to provide a uniform foundation for expression of security checklists and other configuration guidance, and thereby foster more widespread application of good security practices.

ISO/IEC 15504-6:2013 : Information technology - Process assessment - Part 6: An exemplar system life cycle process assessment model

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 15504-6:2013 constitutes a Process Assessment Model, conformant with the requirements of ISO/IEC 15504-2, for the assessment of process capability of system life cycle processes.

The Process Dimension of this Process Assessment Model is based upon the Process Reference Model contained in ISO/IEC 15288.

ISO/IEC 15504-6:2013 provides a new Process Dimension for the Process Assessment Model derived from the revised Process Reference Model contained in ISO/IEC 15288:2008.

The scope of ISO/IEC 15504-6:2013 is consistent with the scope of ISO/IEC 15504-5 in order to assist situations where assessment is being made of both system and software life cycle processes.

Users of ISO/IEC 15504-6:2013 may freely reproduce the detailed descriptions contained in the exemplar assessment model as part of any tool or other material to support the performance of process assessments, so that it can be used for its intended purpose.

ISO/IEC 1539-1:2010/Cor2:2013 : Corrigendum

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 13818-1:2013 : Information technology - Generic coding of moving pictures and associated audio information: Systems

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 13818-1:2013 specifies the system layer of the coding. It was developed principally to support the combination of the video and audio coding methods defined in ISO/IEC 13818-2 and ISO/IEC 13818-3. The system layer supports six basic functions:

the synchronization of multiple compressed streams on decoding;
the interleaving of multiple compressed streams into a single stream;
the initialization of buffering for decoding start up;
continuous buffer management;
time identification;
multiplexing and signalling of various components in a system stream.

ISO/IEC 29182-2:2013 : Information technology - Sensor networks: Sensor Network Reference Architecture (SNRA) - Part 2: Vocabulary and terminology

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 29182-2:2013 is intended to facilitate the development of International Standards in sensor networks. It presents terms and definitions for selected concepts relevant to the field of sensor networks. It establishes a general description of concepts in this field and identifies the relationships among those concepts. It may also be used as guidance for development of other parts of ISO/IEC 29182 and any other sensor network related standard.

ISO/TR 22899-2:2013 : Determination of the resistance to jet fires of passive fire protection - Part 2: Guidance on classification and implementation methods

Tue, 18 Jun 2013 08:27:02 -0500

The test specified in ISO 22899-1 is designed to give an indication of how passive fire protection materials will perform in a jet fire.

ISO/TR 22899-2:2013 provides: background information on the applicability and validation of the jet fire test; further details on testing pipe penetration seals; guidance on the interpretation of the tests results and on an optional classification system; guidance on the combination of results from hydrocarbon furnace tests and resistance to jet fire tests.

ISO 22899-1 describes the thickness of fire protection material (sometimes referred to as passive fire protection; PFP) required to resist the application of a ?jet fire'. ISO/TR 22899-2:2013 provides information on the ?erosion factor' which is the additional thickness required above and beyond that required to satisfy the relevant criteria of ISO 834 (or other national or regional standards designed to evaluate the fire resistance with respect to a fully developed fire) for the element/construction under test.

ISO/TR 19201:2013 : Mechanical vibration - Methodology for selecting appropriate machinery vibration standards

Tue, 18 Jun 2013 08:27:02 -0500

ISO/TR 19201:2013 provides guidance for selecting appropriate vibration standards for specific machine types, and thus selecting the appropriate vibration measurement and evaluation method. Synopses are given of ISO 10816 (evaluation of machine vibration on non-rotating parts) and ISO 7919 (evaluation of machine vibration on rotating parts), together with further International Standards related to machinery.

ISO/TR 19201:2013 provides an overview of the relevant International Standards, giving a summary of their scopes. It also provides a theoretical, analytical basis for establishing whether vibration measurements should be carried out on non-rotating parts, rotating shafts or both for those machines where no previous experience exists. It is not intended to supersede established manufacturers' or users' practical experience with specific machine types since there can be specific features associated with a particular machine which lead to a different selection of the most relevant measurement procedure.

The aim of ISO/TR 19201:2013 is not to equip the reader with all the technical details provided in the International Standards necessary to carry out a measurement or evaluation task on a particular machine; rather it guides the reader to the appropriate International Standards. It is these International Standards that provide the necessary details; and then, with suitable training, the reader is in a position to carry out the measurement or evaluation task.

ISO/TR 17370:2013 : Application Guideline on Data Carriers for Supply Chain Management

Tue, 18 Jun 2013 08:27:02 -0500

ISO 17370:2013 specifies a method to establish compatibility among various data carriers such as linear symbols, two-dimensional symbols and RFID, as well as their one-to-one relationship by illustrating the structure supporting the basic ISO-compliant supply chain control system. In particular, it

specifies the relationship of various global standards related to the supply chain,

illustrates the types and data structures in the layered supply chain network,

specifies the relationship among the layered structure of the supply chain,

specifies the management of serial numbers in supply chain management,

specifies data storage on the named data carriers,

specifies the required data volume for each data carrier,

specifies the data structure between the data carrier and the reader (interrogator),

specifies the data structure between the host system (computer) and the reader (interrogator), and

illustrates complex data carriers (rewritable hybrid media, etc.).

ISO/TR 17350:2013 : Direct Marking on Plastic Returnable Transport Items (RTIs)

Tue, 18 Jun 2013 08:27:02 -0500

ISO 17350:2013 provides guidance on

returnable transport items (RTIs),

identification codes used for RTIs,

specifications for two-dimensional symbols,

method for direct marking, and

reading method for direct marking.

ISO/IEC 29192-4:2013 : Information technology - Security techniques - Lightweight cryptography - Part 4: Mechanisms using asymmetric techniques

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 29192-4:2013 specifies three lightweight mechanisms using asymmetric techniques:

a) a unilateral authentication mechanism based on discrete logarithms on elliptic curves;

b) an authenticated lightweight key exchange (ALIKE) mechanism for unilateral authentication and establishment of a session key;

c) an identity-based signature mechanism.

ISO/TR 17098:2013 : Packaging material recycling - Report on substances and materials which may impede recycling

Tue, 18 Jun 2013 08:27:02 -0500

ISO/TR 17098:2013 provides a non-exhaustive overview of substances and materials that can cause a sustained impediment to recycling activities and is intended to assist in the assessment requirements set out in ISO 18604.

It describes substances or materials which cause problems or inhibit the recycling process, or which have a negative influence on the quality of recycled material, where technical solutions are not expected to be developed in the near future.

These examples are, however, qualified by the fact that the recycling operations can vary regionally, that technology is constantly changing, and that the use to which the recycled material is put will also determine whether the presence of such substances and materials is a problem.

ISO/TR 13097:2013 : Guidelines for the characterization of dispersion stability

Tue, 18 Jun 2013 08:27:02 -0500

ISO/TR 13097:2013 addresses the stability characterization of liquid dispersions (suspensions, emulsions, foams and mixtures thereof) for applications, such as new product design, optimization of existing products, quality control during processing and during usage of the product. The stability of a dispersion in the sense of ISO/TR 13097:2013 is defined in terms of the change in one or more physical properties over a given time period.

ISO/IEC 9594-8:2008/Cor3:2013 : Corrigendum

Tue, 18 Jun 2013 08:27:02 -0500

ISO/IEC 12785-1:2009/Cor1:2013 : Corrigendum

Tue, 18 Jun 2013 08:27:02 -0500

ISO 6847:2013 : Welding consumables - Deposition of a weld metal pad for chemical analysis

Tue, 18 Jun 2013 08:27:01 -0500

ISO 6847:2013 specifies the procedure to be used for deposition of a weld metal pad for chemical analysis. ISO 6847:2013 applies to deposition of a weld metal pad by use of covered electrodes, wire electrodes for gas shielded metal arc welding, tubular cored electrodes for gas shielded metal arc welding and for non-gas shielded metal arc welding, tubular cored rods for gas tungsten arc welding, and wire-flux combinations for submerged arc welding. ISO 6847:2013 is applicable to welding consumables for non-alloy and fine grain steels, high strength steels, creep-resisting steels, stainless and heat-resisting steels, nickel and nickel alloys, and copper and copper alloys.

ISO 9927-1:2013 : Cranes - Inspections - Part 1: General

Tue, 18 Jun 2013 08:27:01 -0500

ISO 9927:2013 specifies the general requirements for inspections to be carried out on cranes as defined in ISO 4306-1. Additional requirements for particular types of cranes are intended to be covered by the relevant specific parts of ISO 9927.

ISO 9513:2012/Cor1:2013 : Corrigendum

Tue, 18 Jun 2013 08:27:01 -0500

ISO 8277:2013 : Ships and marine technology - Pipework and machinery - Information transfer

Tue, 18 Jun 2013 08:27:01 -0500

ISO 8277:2013 specifies the minimum data needed for the prefabrication and assembly of pipework and for its transfer from engineering departments to workshops in the shipbuilding industry.

ISO 8277:2013 is applicable to written information needed for construction of piping installations that marine piping equipment manufacturers submit through specifications and instructions to shipyards on shipbuilding.

ISO 8277:2013 is not applicable to the generation, type presentation and filing organization of this data.

ISO 7001:2007/Amd1:2013 : - Amendment 1

Tue, 18 Jun 2013 08:27:01 -0500

ISO 6358-1:2013 : Pneumatic fluid power - Determination of flow-rate characteristics of components using compressible fluids - Part 1: General rules and test methods for steady-state flow

Tue, 18 Jun 2013 08:27:00 -0500

ISO 6358-1:2013 specifies a steady-state method for testing pneumatic fluid power components that use compressible fluids, i.e. gases, and that have internal flow paths that can be either fixed or variable in size, to determine their flow-rate characteristics. ISO 6358-1:2013 does not apply to components whose flow coefficient is unstable during use, i.e. components that exhibit remarkable hysteretic behaviour (because they can contain flexible parts that deform under the flow) or that have an internal feedback phenomenon (such as regulators). In addition, it does not apply to components that exchange energy with the fluid during flow-rate measurement, e.g. cylinders, accumulators, etc.

ISO 6358-1:2013 specifies requirements for the test installation, the test procedure, and the presentation of results for the steady-state method.

ISO 5951:2013 : Hot-rolled steel sheet of higher yield strength with improved formability

Tue, 18 Jun 2013 08:27:00 -0500

ISO 5951:2013 applies to all grades of hot-rolled steel sheet of higher yield strength with improved formability. The steel is killed, made according to a fine grain practice and has a suitable chemical composition, including microalloying elements, to provide improved formability. The product is intended for the fabrication of parts requiring better formability than is provided by normal high yield strength steel sheet. It is generally used in the delivered condition.

Because of the combination of higher strength and improved formability, it is possible to obtain savings in mass along with better weldability.

ISO 5951:2013 does not cover steel intended for boilers or pressure vessels, steels designated as commercial quality or drawing quality (covered in ISO 3573), steels designated as weathering steels, having increased atmospheric corrosion resistance, or lower yield strength steels having less formability compared with those in ISO 5951:2013 (covered in ISO 4995 and ISO 4996).

ISO 5892:2013 : Rubber building gaskets - Materials for preformed solid vulcanized structural gaskets - Specification

Tue, 18 Jun 2013 08:27:00 -0500

ISO 5892:2013 specifies material requirements for preformed, solid vulcanized rubber structural gaskets in sealing and supporting applications for buildings.

ISO 4211-3:2013 : Furniture - Tests for surface finishes - Part 3: Assessment of resistance to dry heat

Tue, 18 Jun 2013 08:27:00 -0500

ISO 4211-3:2013 specifies a method for the assessment of the resistance to dry heat of all rigid furniture surfaces regardless of materials.

It does not apply to leather and textile surfaces.

ISO 3452-1:2013 : Non-destructive testing - Penetrant testing - Part 1: General principles

Tue, 18 Jun 2013 08:27:00 -0500

ISO 3452-1:2013 specifies a method of penetrant testing used to detect discontinuities, e.g. cracks, laps, folds, porosity and lack of fusion, which are open to the surface of the material to be tested. It is mainly applied to metallic materials, but can also be performed on other materials, provided that they are inert to the test media and not excessively porous (castings, forgings, welds, ceramics, etc.)

It also includes requirements for process and control testing, but is not intended to be used for acceptance criteria and gives neither information relating to the suitability of individual test systems for specific applications nor requirements for test equipment.

ISO 3826-1:2013 : Plastics collapsible containers for human blood and blood components - Part 1: Conventional containers

Tue, 18 Jun 2013 08:27:00 -0500

ISO 3826-1:2013 specifies requirements, including performance requirements, for plastics collapsible, non-vented, sterile containers complete with collecting tube outlet port(s), integral needle, and with optional transfer tube(s), for the collection, storage, processing, transport, separation, and administration of blood and blood components. The plastics containers may contain anticoagulant and/or preservative solutions, depending on the application envisaged.

ISO 3826-1:2013 is also applicable to multiple units of plastics containers, e.g. to double, triple, quadruple, or multiple units.

Unless otherwise specified, all tests specified in ISO 3826-1:2013 apply to the plastics container as prepared ready for use.

ISO 4211-2:2013 : Furniture - Tests for surface finishes - Part 2: Assessment of resistance to wet heat

Tue, 18 Jun 2013 08:27:00 -0500

ISO 4211-2:2013 specifies a method for the assessment of the resistance to wet heat of all rigid furniture surfaces regardless of materials.

It does not apply to leather and textile surfaces.

ISO 18438:2013 : Space data and information transfer systems - Spacecraft Onboard Interface Services - Subnetwork Test Service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18438:2013 is one of a family of documents specifying the SOIS-compliant services to be provided by onboard subnetworks.

ISO 18438:2013 defines services and service interfaces provided by the SOIS Subnetwork Test Service. Its scope is to specify the service only and not to specify methods of providing the service over a variety of onboard data links.

ISO 18438:2013 conforms to the principles set out in the Spacecraft Onboard Interface Services Green Book and is intended to be applied together with it. The protocols which provide this service are to be documented for individual links, and this may be in the purview of individual missions, agencies, or CCSDS, depending on future circumstance.

ISO 22669:2013 : Space data and information transfer systems - Space link extension (SLE) - Return-all-frames service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 22669:2013 defines the space link extension (SLE) return-all-frames (RAF) service in conformance with the SLE reference model (ISO 15396:2007). The RAF service is an SLE transfer service that delivers to a mission user all telemetry frames from one space link physical channel.

ISO 22669:2013 defines the RAF service in terms of

the operations necessary to provide the service,
the parameter data associated with each operation,
the behaviors that result from the invocation of each operation, and
the relationship between, and the valid sequence of, the operations and resulting behaviors.

It does not specify

individual implementations or products,
the implementation of entities or interfaces within real systems,
the methods or technologies required to acquire telemetry frames from signals received from a spacecraft,
the methods or technologies required to provide a suitable environment for communications, or
the management activities required to schedule, configure, and control the RAF service.

ISO 22667:2013 : Space data and information transfer systems - Communications operation procedure-1

Tue, 18 Jun 2013 08:26:59 -0500

ISO 22667:2013 specifies the communications operation procedure-1 (COP-1). This procedure is used with the telecommand (TC) space data link protocol (as defined in ISO 22664:2013) to enable the delivery of service data units to the receiving end of the layer above, correct and without omission or duplication, and in the same sequential order in which they were received from the layer above at the sending end.

ISO 22667:2013 defines the COP-1 in terms of

the interfaces with the other procedures,
the internal variables used by the protocol entity,
the actions performed by the protocol entity, and
the state transitions of the protocol entity.

It does not specify

individual implementations or products,
the implementation of service interfaces within real systems,
the methods or technologies required to perform the procedures, or
the management activities required to configure and control the protocol.

ISO 22664:2013 : Space data and information transfer systems - TC (telecommand) space data link protocol

Tue, 18 Jun 2013 08:26:59 -0500

ISO 22664:2013 specifies the telecommand (TC) space data link protocol. This protocol is a data link layer protocol (as defined in ISO/IEC 7498-1) intended for use over ground-to-space or space-to-space communications links by space missions.

ISO 22664:2013 defines the TC space data link protocol in terms of

the services provided to the users of this protocol,
the protocol data units employed by the protocol, and
the procedures performed by the protocol.

It does not specify

individual implementations or products,
the implementation of service interfaces within real systems,
the methods or technologies required to perform the procedures, or
the management activities required to configure and control the protocol.

ISO 21549-1:2013 : Health informatics - Patient healthcard data - Part 1: General structure

Tue, 18 Jun 2013 08:26:59 -0500

ISO 21549-1:2013 defines a general structure for the different types of data to be defined in other parts of ISO 21549 using UML notation. ISO 21549 defines data structures held on patient healthcards compliant with the physical dimensions of ID-1 cards, as defined by ISO/IEC 7810.

ISO 19932-2:2013 : Equipment for crop protection - Knapsack sprayers - Part 2: Test methods

Tue, 18 Jun 2013 08:26:59 -0500

ISO 19932-2:2013 specifies test methods for the verification of requirements of ISO 19932-1:2013 for knapsack sprayers carried on the back or shoulder of the operator for use with plant protection products.

It is applicable to lever-operated knapsack sprayers, knapsack compression sprayers and knapsack sprayers driven by an engine or electric motor using hydraulic pressure atomisation of the spray liquid, with a nominal volume of more than 3 l for their intended use primarily in agriculture and horticulture.

It does not apply to knapsack mistblowers according to ISO 28139.

ISO 19932-1:2013 : Equipment for crop protection - Knapsack sprayers - Part 1: Safety and environmental requirements

Tue, 18 Jun 2013 08:26:59 -0500

ISO 19932-1:2013 specifies the safety and environmental requirements and their means of verification for the design and construction of knapsack sprayers carried on the back or shoulder of the operator for use with plant protection products. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.

It is applicable to lever-operated knapsack sprayers, knapsack compression sprayers and knapsack sprayers driven by an engine or electric motor using hydraulic pressure atomisation of the spray liquid, with a nominal volume of more than 3 l, for their intended use primarily in agriculture and horticulture.

It does not apply to knapsack mistblowers according to ISO 28139.

ISO 19932-1:2013 deals with all significant hazards, hazardous situations and hazardous events relevant to knapsack sprayers when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, excepting the hazards arising from: static electricity; explosion or fire from chemicals for spraying; and insufficient structural integrity.

ISO 19932-1:2013 is not applicable to knapsack sprayers which are manufactured before the date of its publication.

ISO 19232-5:2013 : Non-destructive testing - Image quality of radiographs - Part 5: Determination of the image unsharpness value using duplex wire-type image quality indicators

Tue, 18 Jun 2013 08:26:59 -0500

ISO 19232-5:2013 specifies a method of determining the total image unsharpness of radiographs and real-time radioscopic systems.

ISO 19232-4:2013 : Non-destructive testing - Image quality of radiographs - Part 4: Experimental evaluation of image quality values and image quality tables

Tue, 18 Jun 2013 08:26:59 -0500

ISO 19232-4:2013 gives instructions for the determination of image quality values and image quality tables.

If the IQI requirements specified in ISO 19232-3 cannot be used because, for example, the absorption coefficients of the IQI material and the inspected material differ by more than 30 %, test exposures are necessary to determine acceptance of image quality values. The image quality values achieved by the test exposures are required for all exposures made under the same radiographic conditions.

ISO 19232-3:2013 : Non-destructive testing - Image quality of radiographs - Part 3: Image quality classes

Tue, 18 Jun 2013 08:26:59 -0500

ISO 19232-3:2013 specifies the minimum image quality values to ensure a uniform radiographic quality. It applies to the two types of image quality indicator as detailed in ISO 19232-1 for wire-type IQI and ISO 19232-2 for step/hole-type IQI and for the two techniques described in ISO 5579. Values are specified for the two classes of radiographic technique specified in ISO 5579.

ISO 19232-2:2013 : Non-destructive testing - Image quality of radiographs - Part 2: Determination of the image quality value using step/hole-type image quality indicators

Tue, 18 Jun 2013 08:26:59 -0500

ISO 19232-2:2013 specifies a device and a method for the determination of the image quality of radiographs using step/hole-type image quality indicators.

ISO 19232-1:2013 : Non-destructive testing - Image quality of radiographs - Part 1: Determination of the image quality value using wire-type image quality indicators

Tue, 18 Jun 2013 08:26:59 -0500

ISO 19232-1:2013 specifies a device and a method for the determination of the image quality of radiographs using wire-type image quality indicators.

ISO 19012-1:2013 : Microscopes - Designation of microscope objectives - Part 1: Flatness of field/Plan

Tue, 18 Jun 2013 08:26:59 -0500

ISO 19012-1:2013 specifies the use of the marking "Plan" on microscope objectives, and defines the diameter of the sharp region of the primary image of a flat object surface. ISO 19012-1:2013 applies to visual observation using the combination of objective lens, tube lens and eyepiece, as specified by the manufacturer.

This marking is consistent with ISO 8578.

ISO 18902:2013 : Imaging materials - Processed imaging materials - Albums, framing and storage materials

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18902:2013 specifies the principal physical and chemical requirements for album, storage and framing materials to prevent damage to processed or printed imaging materials over time. It covers requirements for:

paper and paperboard;

plastics;

metals;

writing instruments;

adhesives;

tapes;

self-adhesive labelling materials;

stamping inks and pads;

framing and glazing materials used as, or in the construction of, storage and display materials for black-and-white or colour reflection prints or negatives made with traditional silver-halide and silver dye bleach photographic materials;

dye- and pigment-based inkjet, dye diffusion thermal transfer ("dye sublimation"), and liquid- and dry-toner electrophotographic digital prints.

ISO 18776:2008/Amd1:2013 : - Amendment 1

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18446:2013 : Space data and information transfer systems - Space Link Extension - Application Program Interface for the Forward Space Packet Service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18446:2013 specifies extensions to the API needed for support of the Forward Space Packet Service defined in CCSDS 912.3-B-1.

ISO 18446:2013 defines extensions to the SLE API in terms of:

the FSP-specific functionality provided by API components;
the FSP-specific interfaces provided by API components; and
the externally visible behavior associated with the FSP interfaces exported by the components.

It does not specify:

individual implementations or products;
the internal design of the components; and
the technology used for communications.

ISO 18446:2013 defines only interfaces and behavior that must be provided by implementations supporting the Forward Space Packet service in addition to the specification in ISO/IEC 14882.

ISO 18445:2013 : Space data and information transfer systems - Space Link Extension - Application Program Interface for the Forward CLTU Service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18445:2013 specifies extensions to the API needed for support of the Command Link Transmission Unit (CLTU) service defined in CCSDS 912.1-B-2.

ISO 18445:2013 defines extensions to the SLE API in terms of:

the CLTU-specific functionality provided by API components;
the CLTU-specific interfaces provided by API components; and
the externally visible behavior associated with the CLTU interfaces exported by the components.

It does not specify

individual implementations or products;
the internal design of the components; and
the technology used for communications.

ISO 18445:2013 defines only interfaces and behavior that must be provided by implementations supporting the forward CLTU service in addition to the specification in CCSDS 914.0-M-1.

ISO 22839:2013 : Intelligent transport systems - Forward vehicle collision mitigation systems - Operation, performance, and verification requirements

Tue, 18 Jun 2013 08:26:59 -0500

ISO 22839:2013 specifies the concept of operation, minimum functionality, system requirements, system interfaces, and test methods for Forward Vehicle Collision Mitigation Systems (FVCMS). It specifies the behaviors that are required for FVCMS, and the system test criteria necessary to verify that a given implementation meets the requirements of ISO 22839:2013. Implementation choices are left to system designers, wherever possible.

ISO 18443:2013 : Space data and information transfer systems - Space Link Extension - Application Program Interface for Return Channel Frames Service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18443:2013 specifies extensions to the API needed for support of the Return Channel Frames (RCF) service defined in CCSDS 911.2-B-1.

ISO 18443:2013 defines extensions to the SLE API in terms of:

the RCF-specific functionality provided by API components;
the RCF-specific interfaces provided by API components; and
the externally visible behavior associated with the RCF interfaces exported by the components.

It does not specify:

individual implementations or products;
the internal design of the components; and
the technology used for communications.

ISO 18443:2013 defines only interfaces and behavior that must be provided by implementations supporting the Return Channel Frames service in addition to the specification in CCSDS 914.0-M-1.

ISO 23273:2013 : Fuel cell road vehicles - Safety specifications - Protection against hydrogen hazards for vehicles fuelled with compressed hydrogen

Tue, 18 Jun 2013 08:26:59 -0500

ISO 23273:2013 specifies the essential requirements for fuel cell vehicles (FCV) with respect to the protection of persons and the environment inside and outside the vehicle against hydrogen-related hazards.

It applies only to such FCV where compressed hydrogen is used as fuel for the fuel cell system.

ISO 23273:2013 does not apply to manufacturing, maintenance, and repair.

The requirements of ISO 23273:2013 address both normal operating (fault-free) and single-fault conditions of the vehicles.

ISO 18441:2013 : Space data and information transfer systems - Space Link Extension - Application Program Interface for Transfer Services - Core Specification

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18441:2013 defines a C++ Application Program Interface (API) for CCSDS Space Link Extension (SLE) Transfer Services, which is independent of any specific technology used for communications between an SLE service user and an SLE service provider.

ISO 18441:2013 defines the Application Program Interface in terms of:

the components that provide the services of the API;
the functionality provided by each of the components;
the interfaces provided by each of the components; and
the externally visible behavior associated with the interfaces exported by the components.

It does not specify:

individual implementations or products;
the internal design of the components; and
the technology used for communications.

ISO 18441:2013 defines those aspects of the Application Program Interface which are common for all SLE service types or for a subset of the SLE service types, e.g. all return link services or all forward link services. It also defines a framework for specification of service type-specific elements of the API. Service-specific aspects of the API are defined by supplemental Recommended Practice documents for SLE return link services and SLE forward link services.

ISO 18441:2013 for the Application Program Interface responds to the requirements imposed on such an API by the CCSDS SLE transfer service Recommended Standards that were available when ISO 18441:2013 was released.

ISO 18440:2013 : Space data and information transfer systems - Space Link Extension - Internet Protocol for Transfer Services

Tue, 18 Jun 2013 08:26:59 -0500

The Space Link Extension (SLE) Reference Model identifies a set of SLE Transfer Services that enable missions to send forward space link data units to a spacecraft and to receive return space link data units from a spacecraft. A subset of these services is specified by the SLE Transfer Service Recommended Standards. The SLE Transfer Service Recommended Standards specify:

the operations necessary to provide the transfer service;
the parameter data associated with each operation;
the behaviors that result from the invocation of each operation; and
the relationship between, and the valid sequence of, the operations and resulting behaviors.

However, they deliberately do not specify the methods or technologies required for communications.

ISO 18440:2013 defines a protocol for transfer of SLE Protocol Data Units (PDUs) defined in the SLE Transfer Service Recommended Standards using the Internet protocols TCP (Transmission Control Protocol and IP (Internet Protocol) for data transfer and the Abstract Syntax Notation One (ASN.1) for data encoding. This protocol is referred to as the Internet SLE Protocol One (ISP1).

ISO 18440:2013 defines a protocol for transfer of SLE PDUs between an SLE user and an SLE provider system in terms of:

the procedures used to establish and release associations;
the messages exchanged on an established association;
the procedures used to monitor the status of data communication connections; and
the methods used to ensure that data are converted between different formats and representations on different platforms.

It does not specify:

individual designs, implementations, or products;
the configuration of the data communications infrastructure, including configuration of the TCP and IP protocols;
the means by which addresses (IP addresses and TCP port numbers) are agreed, assigned, and communicated.

ISO 18440:2013 responds to the requirements imposed by the International Standards for SLE transfer services that were available when this International Standard was released. The protocol specified in ISO 18440:2013 conforms to the requirements on data communication services set forth in those International Standards.

ISO 18439:2013 : Space data and information transfer systems - Space Communication Cross Support - Service Management - Service Specification

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18439:2013 defines a set of Space Communication Cross Support Service Management (SCCS-SM) services by which space link service providers and space missions exchange information needed to arrange spacecraft contact periods and establish the operating parameters of the space link services and cross support transfer services during those contact periods.

ISO 22670:2013 : Space data and information transfer systems - Space link extension (SLE) - Return-channel-frames service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 22670:2013 defines the space link extension (SLE) return-channel-frames (RCF) service in accordance with the SLE Reference Model (ISO 15396:2007). The RCF service is an SLE transfer service that delivers to a mission user all telemetry frames from one master channel or one virtual channel.

ISO 22670:2013 defines the RCF service in terms of

the operations necessary to provide the service,
the parameter data associated with each operation,
the behaviors that result from the invocation of each operation, and
the relationship between, and the valid sequence of, the operations and resulting behaviors.

It does not specify

individual implementations or products,
the implementation of entities or interfaces within real systems,
the methods or technologies required to acquire telemetry frames from signals received from a spacecraft,
the methods or technologies required to provide a suitable environment for communications, or
the management activities required to schedule, configure, and control the RCF service.

ISO 18428:2013 : Space data and information transfer systems - Spacecraft Onboard Interface Services - Subnetwork Device Discovery Service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18428:2013 is one of a family of documents specifying the SOIS-compliant services to be provided by onboard subnetworks.

ISO 18428:2013 defines services and service interfaces provided by the SOIS Subnetwork Device Discovery Service. Its scope is to specify the service only and not to specify methods of providing the service over a variety of onboard data links.

ISO 18428:2013 conforms to the principles set out in the Spacecraft Onboard Interface Services Green Book and is intended to be applied together with it. The protocols which provide this service are to be documented for individual links, and this can be in the purview of individual missions, agencies, or CCSDS, depending on future circumstance.

ISO 18427:2013 : Space data and information transfer systems - Spacecraft Onboard Interface Services - Subnetwork Synchronization Service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18427:2013 is one of a family of documents specifying the SOIS-compliant services to be provided by onboard subnetworks.

ISO 18427:2013 defines services and service interfaces provided by the SOIS Subnetwork Synchronisation Service. Its scope is to specify the service only and not to specify methods of providing the service over a variety of onboard data links.

ISO 18427:2013 conforms to the principles set out in the Spacecraft Onboard Interface Services Green Book and is intended to be applied together with it. The protocols which provide this service are to be documented for individual links, and this can be in the purview of individual missions, agencies, or CCSDS, depending on future circumstances.

ISO 18426:2013 : Space data and information transfer systems - Spacecraft Onboard Interface Services - Subnetwork Memory Access Service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18426:2013 is one of a family of documents specifying the SOIS-compliant services to be provided by onboard subnetworks.

ISO 18426:2013 defines services and service interfaces provided by the SOIS Subnetwork Memory Access Service. Its scope is to specify the service only and not to specify methods of providing the service over a variety of onboard data links.

ISO 18426:2013 conforms to the principles set out in the Spacecraft Onboard Interface Services Green Book and is intended to be applied together with it. The protocols which provide this service are to be documented for individual links, and this can be in the purview of individual missions, agencies, or CCSDS, depending on future circumstances.

ISO 18425:2013 : Space data and information transfer systems - Spacecraft Onboard Interface Services - Subnetwork Packet Service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18425:2013 is one of a family of documents specifying the SOIS-compliant services to be provided by onboard subnetworks.

ISO 18425:2013 defines services and service interfaces provided by the SOIS Subnetwork Packet Service. Its scope is to specify the service only and not to specify methods of providing the service over a variety of onboard data links.

ISO 18425:2013 conforms to the principles set out in the Spacecraft Onboard Interface Services Green Book and is intended to be applied together with it. The protocols which provide this service are to be documented for individual links, and this can be in the purview of individual missions, agencies, or CCSDS, depending on future circumstances.

ISO 18424:2013 : Space data and information transfer systems - XML Telemetric and Command Exchange (XTCE)

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18424:2013 addresses the need for a standardized information model capable of supporting Telemetry/Telecommand (TM/TC) definitions across the widest possible range of space domain activities. The goal is to allow TM/TC definitions to be exchanged between different organizations and systems, often at the boundaries of mission phases, without the need for customized import/export, re-validation, or even re-implementation of mission databases.

The scope of ISO 18424:2013 is limited to the satellite telemetry and commanding meta-data constructs necessary to perform satellite and payload data processing. ISO 18424:2013 includes the meta-data needed to:

Define the structure and sequence of both CCSDS packets and TDM frames;
Define the data manipulation required for packaging and unpacking of individual data items;
Describe command data including command identification, argument specification, and validation criteria;
Define parameter and command encoding;
Define data properties including including default values, validity criteria, and data dependencies.

The scope of ISO 18424:2013 does not extend to:

Data distribution mechanisms or rules;
Command and data protocol specifications;
RF or analog stream characterization;
Data grouping including aggregation and coherent data sets;
Data representation (visualization properties);
Scheduling configuration properties;
Orbital properties;
Displays;
Flight Software.

ISO 18424:2013 addresses only the definition of TM/TC data, but is not a specification for the transfer of live or historical TM/TC data. It is a meta-data specification, not a data specification.

ISO 18423:2013 : Space data and information transfer systems - Pseudo-Noise (PN) Ranging Systems

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18423:2013 provides a Recommendation for Space Data System Standards in the area of transparent and regenerative Pseudo-Noise (PN) ranging systems. The PN ranging system is used to measure the round-trip light time between a ground station and a spacecraft. Regenerative ranging is primarily relevant for low Signal-to-Noise Ratio (SNR) cases like those seen in deep space missions; transparent ranging is more suitable for high SNR cases or when high accuracy ranging is not required.

ISO 18423:2013 defines both transparent and regenerative PN ranging systems for non-data relay satellite users. The specification for PN code components and generation, on-board spacecraft regenerative/transparent processing, ground station processing, and uplink and downlink signal modulation are defined. ISO 18423:2013 does not specify individual implementations or products, implementation of service interfaces within real systems, or the management activities required to configure and control the protocol.

ISO 18382:2013 : Space data and information transfer systems - Spacecraft onboard interface services - RFID-based inventory management systems

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18382:2013 provides recommended practices for the utilization of Radio Frequency Identification (RFID) protocol and communication standards in support of inventory management activities associated with space missions.

The recommended practices contained in ISO 18382:2013 enable member agencies to select the best option(s) available for interoperable RFID-based communications in the support of inventory management applications. The specification of a Recommended Practice facilitates interoperable communications and forms the foundation for cross-support of communication systems between separate member space agencies.

ISO 18382:2013 is targeted towards passive (unpowered) RFID tags transmitting in the 860 MHz ? 960 MHz Ultra High Frequency (UHF) radio band. The recommended practices are applicable to both terrestrial (ground-based) and space-based automated inventory management systems utilizing only passive RFID tags.

Active RFID systems and utilization of RFID tags for precision asset localization are not covered in ISO 18382:2013.

ISO 18381:2013 : Space data and information transfer systems - Lossless multispectral and hyperspectral image compression

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18381:2013 establishes a data compression algorithm applied to digital three-dimensional image data from payload instruments, such as multispectral and hyperspectral imagers, and specifies the compressed data format.

Data compression is used to reduce the volume of digital data to achieve benefits in areas including, but not limited to:

reduction of transmission channel bandwidth;
reduction of the buffering and storage requirement;
reduction of data-transmission time at a given rate.

The characteristics of instrument data are specified only to the extent necessary to ensure multi-mission support capabilities. ISO 18381:2013 does not attempt to quantify the relative bandwidth reduction, the merits of the approaches discussed, or the design requirements for encoders and associated decoders.

ISO 18381:2013 addresses only lossless compression of three-dimensional data, where the requirement is for a data-rate reduction constrained to allow no distortion to be added in the data compression/decompression process.

ISO 18202:2013 : Space data and information transfer systems - Mission operations message abstraction layer

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18202:2013 defines the Mission Operations (MO) Message Abstraction Layer (MAL) in conformance with the service framework specified in CCSDS 520.0-G-3, Mission Operations Services Concept.

The MO MAL is a framework that provides generic service patterns to the Mission Operation services defined in CCSDS 520.0-G-3. These Mission Operations services are defined in terms of the MAL.

ISO 18202:2013 defines, in an abstract manner, the MAL in terms of:

the concepts that it builds upon;
the basic types it provides;
the message headers required by the layer;
the relationship between, and the valid sequence of, the messages and resulting behaviours.

It does not specify:

individual implementations or products;
the implementation of entities or interfaces within real systems;
the methods or technologies required for communications.

ISO 18201:2013 : Space data and information transfer systems - Mission operations reference model

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18201:2013 defines a Mission Operations (MO) reference model which provides a common basis for coordinating the development of CCSDS Recommended Standards for MO service specifications and serves as a reference to maintain the consistency of these Recommended Standards.

The scope of ISO 18201:2013 is the definition of all concepts and terms that establish a common basis for coordinating the development of CCSDS Recommended Standards for MO service specifications.

ISO 17854:2013 : Space data and information transfer systems - Flexible advanced coding and modulation scheme for high rate telemetry applications

Tue, 18 Jun 2013 08:26:59 -0500

ISO 17854:2013 defines an efficient and comprehensive coding and modulation solution able to support a wide range of spectral efficiency values and data rates. The main target is given by high data rate telemetry applications, i.e. Earth Exploration Satellite Service (EESS) telemetry payload, where the increase of the system throughput by means of advanced adaptive techniques is deemed essential in order to fulfil the requirements imposed by future missions.

ISO 17854:2013 presents a turbo-like coding/modulation scheme based on one possible realization of a Serial Concatenated Convolutional Code (SCCC). This scheme makes use of a set of a large variety of modulation techniques (including QPSK, 8PSK, 16APSK, 32APSK, and 64APSK) and a wide range of coding rates. The number of different modulation schemes available, combined with a properly selected coding rate, allows the overall system to make efficient use of the available bandwidth, adapting itself to the variable conditions of the link. The proposed scheme can implement Variable Coding and Modulation (VCM) mode, which varies the transmission scheme to the channel conditions following a predetermined schedule (for example, as a function of the elevation angle). When a channel is available to provide feedback (e.g. via Telecommand), the transmission scheme can be dynamically adjusted using the Adaptive Coding and Modulation (ACM) mode. The proposed coding scheme is easily adapted to any of the available modulation formats thanks to the pragmatic approach adopted: the outputs of the binary encoders are mapped to the considered modulation scheme, after being interleaved. In other words, a bit-interleaved coded modulation scheme is proposed.

The use of SCCC is intended mainly for high data rate applications. The Forward Error Correction (FEC) scheme is based on the concatenation of two simple four-state encoder structures. The SCCC scheme implies a Physical Layer frame of constant length, with pilots inserted in fixed positions. This architecture simplifies the synchronization procedure, thus further allowing fast and efficient acquisition at very high rates for the receiver.

ISO 17854:2013 describes a technique incorporating multiple modulation formats paired with a flexible coding and synchronization method in a tightly integrated fashion. In particular, ISO 17854:2013 provides a series of recommended formats where each format pairs a modulation technique with a tailored implementation of the coding and synchronization method. However, where these modulations and/or codes are recommended in other CCSDS documents, ISO 17854:2013 does not limit the choice of modulations and/or codes consistent with those recommendations.

ISO 17807:2013 : Space data and information transfer systems - Asynchronous message service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 17807:2013 defines a CCSDS Asynchronous Message Service (AMS) for mission data system communications. The service and its protocols implement an architectural concept under which the modules of mission systems, distinct sequential flows of application control logic, whether called processes, tasks, or threads, may be designed as if they were to operate in isolation, each one producing and consuming mission information without explicit awareness of which other modules are currently operating. Communication relationships among such modules are self-configuring; this tends to minimize complexity in the development and operations of modular data systems.

A system built on this model is a society of generally autonomous interoperating modules that may fluctuate freely over time in response to changing mission objectives, module functional upgrades, and recovery from individual module failure. The purpose of AMS, then, is to reduce mission cost and risk by providing standard, reusable infrastructure for the exchange of information among data system modules in a manner that is simple to use, highly automated, flexible, robust, scalable, and efficient.

ISO 17807:2013 specifies the protocol procedures and data units that accomplish automatic configuration of AMS communication relationships, dynamic reconfiguration of those relationships during operations, and the use of those relationships to accomplish the exchange of mission information among data system modules.

ISO 17712:2013 : Freight containers - Mechanical seals

Tue, 18 Jun 2013 08:26:59 -0500

ISO 17712:2013 establishes uniform procedures for the classification, acceptance, and withdrawal of mechanical freight container seals. It provides a single source of information on mechanical seals which are acceptable for securing freight containers in international commerce.

ISO 17380:2013 : Soil quality - Determination of total cyanide and easily liberatable cyanide - Continuous-flow analysis method

Tue, 18 Jun 2013 08:26:59 -0500

ISO 17380:2013 specifies a method for the photometric determination of the total cyanide and easily-liberatable cyanide content in soil using automated distillation/continuous-flow analysis.

ISO 17380:2013 applies to all types of soil with cyanide contents above 1 mg/kg on the basis of dry matter, expressed as cyanide ion.

ISO 24531:2013 : Intelligent transport systems - System architecture, taxonomy and terminology - Using XML in ITS standards, data registries and data dictionaries

Tue, 18 Jun 2013 08:26:59 -0500

ISO 24531:2013 assists ITS standards developers and users of ITS standards who wish to use XML, by providing a consistent definition of the rules and rule references for the use of XML within ITS systems. ISO 24531:2013 defines consistent rules and rule references to provide a framework to be used when implementing XML-based applications in ITS, and particularly in specifying XML in ITS standards, ITS data registries and ITS data dictionaries. ISO 24531:2013 also provides guidance and examples in respect of the use of XML in ITS, and the elaboration of XML within the ASN.1 data definitions required by ISO 14813-6 and ISO 14817.

ISO 26143:2013 : Space data and information transfer systems - Space link extension (SLE) - Return operational control fields service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 26143:2013 defines the space link extension (SLE) return operational control fields (ROCF) service in accordance with the SLE Reference Model (ISO 15396:2007). The ROCF service is an SLE transfer service that delivers to a mission user all operational control fields from one master channel or one virtual channel.

ISO 26143:2013 defines the ROCF service in terms of

the operations necessary to provide the service,
the parameter data associated with each operation,
the behaviors that result from the invocation of each operation, and
the relationship between, and the valid sequence of, the operations and resulting behaviors.

It does not specify

individual implementations or products,
the implementation of entities or interfaces within real systems,
the methods or technologies required to acquire telemetry frames from signals received from a spacecraft,
the methods or technologies required to provide a suitable environment for communications, or
the management activities required to schedule, configure, and control the ROCF service.

ISO 26842-1:2013 : Adhesives - Test methods for the evaluation and selection of adhesives for indoor wood products - Part 1: Resistance to delamination in non-severe environments

Tue, 18 Jun 2013 08:26:59 -0500

ISO 26842-1:2013 gives guidelines to select, by means of delamination-resistance tests, adhesive/wood combinations in non-severe environments in which the products are not exposed to extreme changes in temperature and humidity. A series of exposure cycles at various temperature and humidity values is provided to verify that the adhesive selected, or a product bonded with the adhesive, meets the necessary requirements for resistance to delamination.

ISO 26842-2:2013 : Adhesives - Test methods for the evaluation and selection of adhesives for indoor wood products - Part 2: Resistance to delamination in severe environments

Tue, 18 Jun 2013 08:26:59 -0500

ISO 26842-2:2013 gives guidelines to select, by means of delamination-resistance tests, adhesive/wood combinations for use in wood products placed in severe environments, in which the products are exposed to extreme change of temperature and humidity. A series of exposure cycles at various temperature and humidity values is provided to verify that the adhesive selected, or a product bonded with the adhesive, meets the necessary requirements for resistance to delamination.

ISO 2698:2013 : Diesel engines - Clamp-mounted fuel injectors, types 7 and 28

Tue, 18 Jun 2013 08:26:59 -0500

ISO 2698:2013 specifies dimensions necessary for the mounting of fuel injectors in diesel (compression-ignition) engines. The location of the fuel inlet and leak-off connections, and the dimensions of the clamp are not defined since they vary according to the particular application.

ISO 2698:2013 applies to clamp-mounted injectors of types 7 and 28 made of an integral nozzle and nozzle holder design with a 9,5 mm (nominal) injector shank diameter.

ISO 28841:2013 : Guidelines for simplified seismic assessment and rehabilitation of concrete buildings

Tue, 18 Jun 2013 08:26:59 -0500

The purpose of ISO 28841:2013 is to provide sufficient information to perform the seismic assessment and rehabilitation of the structural concrete building that complies with the limitations established in ISO 28841:2013, for both undamaged structures that are deemed not to comply with the required characteristics for an adequate response at a specified performance level, and for structures that have undergone damage under seismic loadings. The rules of design as set forth in ISO 28841:2013 are simplifications of more elaborate requirements.

ISO 28841:2013 can be used as an alternative to the development of a building code, or equivalent document in countries where no national design codes are available by themselves, or as an alternative to the building code in countries where specifically considered and accepted by the national standards body or other appropriate regulatory organization, and applies to the assessment of earthquake resistance capability and to the seismic rehabilitation design and construction for existing structural concrete buildings.

ISO 29022:2013 : Dentistry - Adhesion - Notched-edge shear bond strength test

Tue, 18 Jun 2013 08:26:59 -0500

ISO 29022:2013 specifies a shear test method used to determine the adhesive bond strength between direct dental restorative materials and tooth structure, e.g. dentine or enamel. The method as described is principally intended for dental adhesives. The method includes substrate selection, storage and handling of tooth structure, as well as the procedure for testing.

ISO 18442:2013 : Space data and information transfer systems - Space Link Extension - Application Program Interface for Return All Frames Service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18442:2013 specifies extensions to the API needed for support of the Return All Frames (RAF) service defined in CCSDS 911.1-B-2.

ISO 18442:2013 defines extensions to the SLE API in terms of:

the RAF-specific functionality provided by API components;
the RAF-specific interfaces provided by API components; and
the externally visible behavior associated with the RAF interfaces exported by the components.

It does not specify

individual implementations or products;
the internal design of the components; and
the technology used for communications.

ISO 18442:2013 defines only interfaces and behavior that must be provided by implementations supporting the Return All Frames service in addition to the specification in CCSDS 914.0-M-1.

ISO 18444:2013 : Space data and information transfer systems - Space Link Extension - Application Program Interface for Return Operational Control Fields Service

Tue, 18 Jun 2013 08:26:59 -0500

ISO 18444:2013 specifies extensions to the API needed for support of the Return Operational Control Fields (ROCF) service defined in CSDS 911.5-B-1.

ISO 18444:2013 defines extensions to the SLE API in terms of:

the ROCF-specific functionality provided by API components;
the ROCF-specific interfaces provided by API components; and
the externally visible behavior associated with the ROCF interfaces exported by the components.

It does not specify:

individual implementations or products;
the internal design of the components; and
the technology used for communications.

ISO 18444:2013 defines only interfaces and behavior that must be provided by implementations supporting the Return Operational Control Fields service in addition to the specification in CCSDS 914.0-M-1.

ISO 15690:2013 : Radiological protection - Recommendations for dealing with discrepancies between personal dosimeter systems used in parallel

Tue, 18 Jun 2013 08:26:58 -0500

ISO 15690:2013 provides recommendations for dealing with discrepancies between dosimeter systems used in parallel, in order to comply with established criteria and national regulations.

ISO 15690:2013 gives guidelines for investigating and analysing the discrepancies between the results of personal dosimetry systems, using two or more dosimeters (often one passive dosimeter and one active dosimeter), worn in parallel by the same worker.

ISO 15690:2013 identifies when the difference between measurements made by personal dosimetry systems used in parallel is considered significant and, hence, needs to be investigated.

It specifies the treatment of this difference.

In ISO 15690:2013, only the personal dose equivalent, Hp(10), from photon radiation is considered. Exposure to beta particles and neutrons might need to be taken into account when identified discrepancies are investigated.

ISO 15690:2013 applies to situations where the period of wearing can be integrated to the same period of time for both systems.

ISO 15638-7:2013 : Intelligent transport systems - Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV) - Part 7: Other applications

Tue, 18 Jun 2013 08:26:58 -0500

ISO 15638-7:2013 provides business framework based on a (multiple) service provider oriented approach for the provision of additional unregulated services to regulated commercial freight vehicles using a common on-board telematics platform, including:

a) definition of the service that a 'Service Provider' has to provide, including a given service level (the service definition comprises service elements such as 'retrieve data from IVS', 'map data to a map with access conditions', etc.);

b) means to realise the service;

c) application data, naming content and quality that an IVS has to deliver;

d) development of (any) rules for the approval and auditing of service providers for non-regulated service provision.

ISO 15638-7:2013 defines the requirements for the scope and framework for all TARV commercial (unregulated) applications. These applications may then be simply instantiated as commercial applications conforming to the requirements of ISO 15638-7:2013, in which case no further standardization is required, so long as conformance can be demonstrated, and service offerings may vary from service provider to service provider. Where it is decided that there is benefit in standardized instantiation to a common format for a particular service, a separate standards deliverable will be required, but may be developed by the consensus of experts in that area of application by reference to ISO 15638-7:2013 in respect of the TARV technical aspects.

ISO 15638 has been developed for use in the context of regulated commercial freight vehicles (hereinafter referred to as 'regulated vehicles'). There is nothing, however, to prevent a jurisdiction extending or adapting the scope to include other types of regulated vehicles, as it deems appropriate.

ISO 15638-5:2013 : Intelligent transport systems - Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV) - Part 5: Generic vehicle information

Tue, 18 Jun 2013 08:26:58 -0500

ISO 15638-5:2013 defines generic basic vehicle and core application data provision to application service providers to be supported by in-vehicle systems (IVS) for cooperative telematics applications for regulated commercial freight vehicles (TARV), and to provide basic vehicle data for cooperative intelligent transport systems.

ISO 15638-5:2013 provides the specifications for generic basic vehicle data that it is required for all TARV IVSs to support and make available to application service providers via a wireless communications link supported by the IVS, in order to support the provision of regulated and commercial application services.

Some further data concepts, while not required in all cases for every TARV in every jurisdiction, may be required generically for all equipment within a particular jurisdiction, or class of TARV within a jurisdiction, in order for the jurisdiction to achieve its regulation of TARVs.

Equipped vehicles operating internationally will need to carry all of the additional data concepts required by all of the jurisdictions within which they operate, in order to determine their core application data. ISO 15638-5:2013 provides standard definitions for these commonly expected additional data concepts.

A second set of (largely complementary) 'basic vehicle' data is required to support interoperable cooperative intelligent transport systems and this is also determined and provided within ISO 15638-5:2013. The framework architecture and many of the protocols are common between both (TARV and C-ITS) sets of requirements, and also with those being adopted by the wider cooperative ITS sector.

ISO 15638-3:2013 : Intelligent transport systems - Framework for collaborative telematics applications for regulated commercial freight vehicles (TARV) - Part 3: Operating requirements, Approval Authority procedures, and enforcement provisions for the providers of regulated services

Tue, 18 Jun 2013 08:26:58 -0500

ISO 15638-3:2013 defines provisions to enable monitoring and enforcement of regulated vehicles and approval authority approval procedures, specifically:

a) Definition of the roles and responsibilities of key entities: user, service provider, jurisdictions, and 'Approval Authorities'

b) Operating requirements ensuring that a cooperative in-vehicle platform can deliver a range of services to both government and industry through open standards and competitive markets

c) Basic service requirements for service providers that are generic and independent of a specific application

d) Requirements for the approval authority approval of IVSs and service providers

e) Legal, regulatory, and enforcement aspects.

The scope includes the requirements for the IVS capability in the vehicle, and the definition of the roles of the service provider, 'Communications Service Provider', IVS installer, 'IVS maintainer', approval authority, and the user, for cooperative telematics applications for regulated commercial freight vehicles.

ISO 15638-2:2013 : Intelligent transport systems - Framework for collaborative Telematics Applications for Regulated commercial freight Vehicles (TARV) - Part 2: Common platform parameters using CALM

Tue, 18 Jun 2013 08:26:58 -0500

ISO 15638-2:2013 defines a generic cooperative ITS service platform for TARV using CALM, including protocol of coding, timing, and performance and support interfaces (such as driver ID card/USB or similar etc.).

ISO 15614-14:2013 : Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 14: Laser-arc hybrid welding of steels, nickel and nickel alloys

Tue, 18 Jun 2013 08:26:58 -0500

ISO 15614-14:2013 specifies how a preliminary welding procedure specification is qualified by welding procedure tests.

ISO 15614-14:2013 defines the conditions for the execution of welding procedure tests and the range of qualification for welding procedures for all practical welding operations within the range of variables listed.

ISO 14577-1:2002 : Metallic materials -- Instrumented indentation test for hardness and materials parameters -- Part 1: Test method

Tue, 18 Jun 2013 08:26:58 -0500

This part of ISO 14577 specifies the method of instrumented indentation test for determination of hardness and other materials parameters for the three ranges given in Table 1.

The macro and micro range are distinguished by the test forces in relation to the indentation depth.

Attention is drawn to the fact that the micro range has an upper limit given by the test force (2 N) and a lower limit given by the indentation depth of 0,2 μm.

The determination of hardness and other materials parameters is given in annex A.

At high contact pressures, damage to the indenter is possible. For this reason in the macro range, hardmetal indenters are often used. For test pieces with very high hardness and modulus of elasticity the influence of indenter deformation on the test result should be taken into account.

Table 1 - Ranges of application
Macro range	Micro range	Nano range^a
2 N ≤ F ≤ 30 kN	2 N > F; h >0,2 μm	h ≤ 0,2 μm
^a For the nano range the mechanical deformation strongly depends on the real shape of indenter tip and the calculated materials parameters are significantly influenced by the contact area function of the indenter used in the testing machine. Therefore careful calibration of both instrument and indenter shape is required in order to achieve an acceptable reproducibility of the materials parameters determined with different machines.

ISO 13686:2013 : Natural gas - Quality designation

Tue, 18 Jun 2013 08:26:58 -0500

ISO 13686:2013 specifies the parameters required to describe finally processed and, where required, blended natural gas.

The main text of ISO 13686:2013 contains a list of these parameters, their units and references to measurement standards. Informative annexes give examples of typical values for these parameters, with the main emphasis on health and safety.

ISO 13073-2:2013 : Ships and marine technology - Risk assessment on anti-fouling systems on ships - Part 2: Marine environmental risk assessment method for anti-fouling systems on ships using biocidally active substances

Tue, 18 Jun 2013 08:26:58 -0500

ISO 13073-2:2013 specifies a risk assessment method that protects the marine environment from the potential negative impacts of anti-fouling systems intentionally using biocidally active substances applied to a ship during its service life. This method can also be modified for use in freshwater environments.

ISO 13073-2:2013 does not provide specific test methods for evaluating the hazards nor recommends usage restrictions for certain anti-fouling systems. It also does not provide an efficacy-evaluation method of the anti-fouling system using a specific substance.

ISO 12932:2013 : Welding - Laser-arc hybrid welding of steels, nickel and nickel alloys - Quality levels for imperfections

Tue, 18 Jun 2013 08:26:58 -0500

ISO 12932:2013 specifies quality levels of imperfections in laser-arc hybrid welded joints for all types of steel, nickel and its alloys. It applies to material thickness ≥0,5 mm.

Three quality levels are given in order to permit application for a wide range of welded fabrication. They are designated by B, C and D. Quality level B corresponds to the highest requirement on the finished weld. The quality levels refer to production quality and not to the fitness-for-purpose of the product manufactured.

ISO 12818:2013 : Glass packaging - Standard tolerances for flaconnage

Tue, 18 Jun 2013 08:26:58 -0500

ISO 12818:2013 specifies the tolerances for the bottles intended to be used for pharmaceutical products, cosmetic and perfumery products and chemical products. The tolerances concerned are brimful capacity, height, diameter and width, and verticality.

ISO 12570:2000/Amd1:2013 : - Amendment 1

Tue, 18 Jun 2013 08:26:58 -0500

ISO 12466-1:2007/Amd1:2013 : - Amendment 1

Tue, 18 Jun 2013 08:26:58 -0500

ISO 16632:2013 : Tobacco and tobacco products - Determination of water content - Gas-chromatographic method

Tue, 18 Jun 2013 08:26:58 -0500

ISO 16632:2013 specifies a gas-chromatographic method for the determination of water content. It is applicable to raw tobacco as well as tobacco taken from finished products. The method is suitable for water contents ranging at least from a mass fraction of 2 % to 55 %.

ISO 16565:2013 : Rubber - Determination of 5-ethylidenenorbornene (ENB) or dicyclopentadiene (DCPD) in ethylene-propylene-diene (EPDM) terpolymers

Tue, 18 Jun 2013 08:26:58 -0500

ISO 16565:2013 specifies the methods to be used to determine the content of 5 ethylidenenorbornene (ENB) or dicyclopentadiene (DCPD) in ethylene-propylene-diene (EPDM) terpolymers in the 0,1 % to 10 % range.

ENB and DCPD are dienes introduced into ethylene-propylene rubbers to generate specific cure properties. Since high precision for diene content determination is important, a Fourier transform infrared spectroscopic (FT IR) method is utilized.

ISO 1629:2013 : Rubber and latices - Nomenclature

Tue, 18 Jun 2013 08:26:58 -0500

ISO 1629:2013 establishes a system of symbols for the basic rubbers in both dry and latex forms, based on the chemical composition of the polymer chain. The purpose is to standardize the abbreviated terms used in industry, commerce and government, and it is not intended to conflict with, but rather to act as a supplement to, existing trade names and trademarks.

ISO 15739:2013 : Photography - Electronic still-picture imaging - Noise measurements

Tue, 18 Jun 2013 08:26:58 -0500

ISO 15739:2013 specifies methods for measuring and reporting the noise versus signal level and dynamic range of digital still cameras. It applies to both monochrome and colour electronic digital still cameras.

ISO 15887:2013 : Space data and information transfer systems - Lossless data compression

Tue, 18 Jun 2013 08:26:58 -0500

ISO 15887:2013 establishes a source-coding data-compression algorithm applied to digital data and specifies how these compressed data shall be inserted into source packets for retrieval and decoding.

Source coding for data compression is a method utilized in data systems to reduce the volume of digital data to achieve benefits in areas including, but not limited to:

reduction of transmission channel bandwidth;
reduction of the buffering and storage requirement;
reduction of data-transmission time at a given rate.

The characteristics of source codes are specified only to the extent necessary to ensure multi-mission support capabilities. ISO 15887:2013 does not attempt to quantify the relative bandwidth reduction, the merits of each approach discussed, or the design requirements for coders and associated decoders. Some performance information is included in CCSDS 120.0-G-2.

ISO 15887:2013 addresses only Lossless source coding, which is applicable to a wide range of digital data, both imaging and non-imaging, where the requirement is for a moderate data-rate reduction constrained to allow no distortion to be added in the data compression/decompression process. The decompression process is not addressed.

ISO 16049-2:2013 : Air cargo equipment - Restraint straps - Part 2: Utilization guidelines and lashing calculations

Tue, 18 Jun 2013 08:26:58 -0500

ISO 16049-2:2013 provides general utilization guidelines and calculation methods adequate to guarantee the effectiveness and ultimate load strength of tie-down/lashing arrangements performed to restrain cargo on board civil transport aircraft during flight:

a) cargo loaded and tied down onto airworthiness approved air cargo pallets, themselves restrained into aircraft lower deck or main deck or upper deck cargo systems meeting the restraint requirements of air cargo pallets approved in accordance with ISO 8097, (NAS3610) or ISO/PAS 21100, or

b) additional tie-down on aircraft structure when necessitated by pallet maximum gross mass or centre of gravity limits, or

c) non-unitized individual pieces of cargo, or pieces of cargo placed onto an unrestrained ("floating") pallet into either lower deck, main deck or upper deck containerized cargo compartments of an aircraft, or

d) individual pieces of load loaded in non-containerized (bulk loaded) baggage or cargo compartments.

ISO 16049-2:2013 applies to cargo tie-down/lashing arrangements using exclusively air cargo restraint straps conforming to ISO 16049-1. Its general recommendations may also be used for tie-down arrangements using other means (e.g. steel cables, rope, other types of straps), but under the user's responsibility as to their adequacy and the strength.

ISO 16049-2:2013 provides industry recognized means of complying with Airworthiness Authorities general regulations applicable to load securing on board civil transport aircraft (see 14 CFR Part 25 and EASA CS-25), and aircraft manufacturers Authority approved Weight and Balance Manuals for each aircraft type as specified therein. It is not the intent of this part of ISO 16049 to specify when restraint straps should be used, but how they should be used. It does not, under any circumstance, supersede the requirements of any of the above documents that take precedence at all times.

ISO 16236:2013 : Crop protection equipment - Test method for the determination of drainable volume and its concentration

Tue, 18 Jun 2013 08:26:58 -0500

ISO 16236:2013 specifies the test method for the determination of the volume and the concentration of the drainable volume of sprayers, in connection to the emptying of the diluted residue of the spray tank by using its outlet and other outlets allowing draining (e.g. suction filter, filling connection) at the end of the cleaning procedure.

ISO 16236:2013 applies to agricultural sprayers used for crop protection and liquid fertiliser applications for both brand new sprayers and sprayers already in use.

ISO 16297:2013 : Milk - Bacterial count - Protocol for the evaluation of alternative methods

Tue, 18 Jun 2013 08:26:58 -0500

ISO 16297|IDF161:2013 gives guidelines for the evaluation of instrumental alternative methods for total bacterial count in raw milk from animals of different species.

ISO 16531:2013 : Surface chemical analysis - Depth profiling - Methods for ion beam alignment and the associated measurement of current or current density for depth profiling in AES and XPS

Tue, 18 Jun 2013 08:26:58 -0500

ISO 16531:2013 specifies methods for the alignment of the ion beam to ensure good depth resolution in sputter depth profiling and optimal cleaning of surfaces when using inert gas ions in Auger electron spectroscopy and X-ray photoelectron spectroscopy. These methods are of two types: one involves a Faraday cup to measure the ion current; the other involves imaging methods. The Faraday cup method also specifies the measurements of current density and current distributions in ion beams. The methods are applicable for ion guns with beams with a spot size below ~1 mm in diameter. The methods do not include depth resolution optimization.

ISO 11297-3:2013 : Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3: Lining with close-fit pipes

Tue, 18 Jun 2013 08:26:57 -0500

ISO 11297-3:2013, in conjunction with ISO 11297-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipe for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.

ISO 11439:2013 : Gas cylinders - High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles

Tue, 18 Jun 2013 08:26:57 -0500

ISO 11439:2013 specifies minimum requirements for light-weight refillable gas cylinders intended only for the on-board storage of high pressure compressed natural gas as a fuel for automotive vehicles to which the cylinders are to be fixed. The service conditions do not cover external loadings that can arise from vehicle collisions, etc.

ISO 11439:2013 covers cylinders of any seamless steel, seamless aluminium alloy or non-metallic material construction, using any design or method of manufacture suitable for the specified service conditions. It does not cover cylinders of stainless steel.

ISO 11439:2013 uses 200 bar as a reference working pressure, but other working pressures can be used.

Cylinders covered by ISO 11439:2013 are designated Type 1, Type 2, Type 3 and Type 4.

ISO 11452-7:2003/Amd1:2013 : - Amendment 1

Tue, 18 Jun 2013 08:26:57 -0500

IEEE C57.12.60-2009/Cor 1-2013 : IEEE Standard Test Procedure for Thermal Evaluation of Insulation Systems for Dry-Type Power and Distribution Transformers, Including Open-Wound, Solid-Cast, and Resin-Encapsulated Transformers

Mon, 17 Jun 2013 20:15:10 -0500

Corrigendum Standard - Active. This corrigendum clarifies temperature control for aging experiments in 4.5.1 that was a result of the combination of the two previous test standards. This corrigendum selects the method from the two which should have been used in the combined test standard represented by the 2009 version. This document also makes one minor editorial change in 4.4.

IEC/TR 62655 Ed. 1.0 b:2013 : Tutorial and application guide for high-voltage fuses

Mon, 17 Jun 2013 15:03:00 -0500

IEC/TR 62655:2013 provides information for understanding the construction, operation and application of high-voltage fuses in general. Current-limiting, expulsion, electronic, and other, non-current-limiting, fuses rated above 1 kV a.c. are all covered, as are North American, European and other application practices. As a technical report, this document contains no requirement and is informative only. Key words: high-voltage fuses

IEC/TS 62720 Ed. 1.0 b:2013 : Identification of units of measurement for computer-based processing

Mon, 17 Jun 2013 15:03:00 -0500

IEC/TS 62720:2013 specifies identifiers for units to support computer-based processing of product data. It provides a survey of quantities with associated collections of internationally standardized as well as non-standardized units used in business and science. It concerns any standard or non-standard units of measure currently in use, in two or more distinct ethno-linguistic groups or nations, at least in one domain of industry, for which an explicit method of conversion to a known standard unit of measure or its equivalent is well documented or evident from external references.

IEC/TS 62796 Ed. 1.0 en:2013 : Energy efficiency in electroheating installations

Mon, 17 Jun 2013 15:03:00 -0500

IEC/TS 62693:2013(E) is applicable to industrial electroheating installations using electric energy as input, alone or in combination with other kinds of energy. However, external combustible fuel energy input is not dealt with, and all considerations begin at the electric only mains frequency source to which the installation is connected. Any external voltage transformation from the supply network to the plant into a special voltage which is fed into the installation is not dealt with in this Technical Specification, since it is not considered a responsibility of the manufacturer of the installation.

IEC/TR 62547 Ed. 2.0 en:2013 : Guidelines for the measurement of high-power damage sensitivity of single-mode fibre to bends - Guidance for interpretation of results

Mon, 17 Jun 2013 15:03:00 -0500

IEC/TR 62547:2013(E) describes two methods for the measurement of the sensitivity of single-mode optical fibres to high-power damage at bends:
- test method 1 - Failure time characterisation as a function of the launch power and bend conditions (bend angle and bend diameter);
- test method 2 - Equilibrium temperature measurement. Results from the two methods can only be compared qualitatively. This second edition cancels and replaces the first edition published in 2009, and constitutes a technical revision. The main changes with respect to the previous edition are:
- updates related to B6 (bend-insensitive) category single-mode fibres);
- update to analysis for test method 2: Maximum temperature specification. Key words: sensitivity of single-mode optical fibres to high-power damage at bends

IEC 62343 Ed. 1.0 en:2013 : Dynamic modules - General and guidance

Mon, 17 Jun 2013 15:03:00 -0500

IEC 62343:2013(E) applies to all commercially available optical dynamic modules and devices. It describes the products covered by the IEC 62343-X series, defines terminology, fundamental considerations and basic approaches. The object of this standard is to:
- establish uniform requirements for operation, reliability and environmental properties of DMs to be implemented in the appropriate DM standard,
- provide assistance to the purchaser in the selection of consistently high-quality DM products for his particular applications, as well as in the consultation of the appropriate specific DM standard(s). This standard covers performance templates, performance standards, reliability qualification requirements, hardware and software interfaces and related testing methods. Keywords: optical dynamic modules and devices, DM

IEC 62323 Ed. 1.0 b:2005 : Dimensions of half pot-cores made of ferrite for inductive proximity switches

Mon, 17 Jun 2013 15:03:00 -0500

IEC 62323:2005 lays down the important dimensions for the mechanical interchangeability of a preferred half pot-core series of ferrite, intended to be used in inductive proximity switches.

IEC 62321-1 Ed. 1.0 b:2013 : Determination of certain substances in electrotechnical products - Part 1: Introduction and overview

Mon, 17 Jun 2013 15:03:00 -0500

IEC 62321-1:2013 refers to the sample as the object to be processed and measured. The nature of the sample and the manner in which it is acquired is defined by the entity carrying out the tests and not by this standard. It provides guidance on the disassembly procedure employed for obtaining a sample. This first edition of IEC 62321-1 is a partial replacement of IEC 62321, forming a structural revision and replacing Clauses 1 to 4.

IEC 62271-109 Ed. 2.1 b:2013 : High-voltage switchgear and controlgear - Part 109: Alternating-current series capacitor by-pass switches CONSOLIDATED EDITION

Mon, 17 Jun 2013 15:03:00 -0500

IEC 62271-109:2008+A1:2013 is applicable to a.c. series capacitor by-pass switches designed for outdoor installation and for operation at frequencies of 50 Hz and 60 Hz on systems having voltages above 52 kV. It is only applicable to by-pass switches for use in three-phase systems. This standard is also applicable to the operating devices of by-pass switches and to their auxiliary equipment. This second edition cancels and replaces the first edition, published in 2006, and constitutes a technical revision. The main changes with respect to the previous edition are listed below:
- By-passing test duty has been split.
- Equivalence regarding applicability of test parameters were reviewed.
- Recovery voltage waveshape during insertion test duty has been recalculated and optimized. An explanatory note on the calculation of the recovery voltage is given in Annex F.
- Withdrawal of the electrical endurance class BP2. Such devices are now covered in informative Annex E.
- Addition of Annex D which gives examples of typical by-pass switch ratings. This consolidated version consists of the second edition (2008) and its amendment 1 (2013). Therefore, no need to order amendment in addition to this publication.

This publication is to be read in conjunction withIEC 62271-100:2008 and IEC 62271-1:2007.

IEC 62319-1-1 Ed. 1.0 b:2005 : Polymeric thermistors - Directly heated positive step function temperature coefficient - Part 1-1: Blank detail specification - Current limiting application

Mon, 17 Jun 2013 15:03:00 -0500

IEC 62319-1-1:2005 is a supplementary document to the generic specification and contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements shall not be considered as being in accordance with IEC specifications nor shall they so be described.

IEC 62271-109 Amd.1 Ed. 2.0 b:2013 : Amendment 1 - High-voltage switchgear and controlgear - Part 109: Alternating-current series capacitor by-pass switches

Mon, 17 Jun 2013 15:02:59 -0500

IEC 62264-1 Ed. 2.0 b:2013 : Enterprise-control system integration - Part 1: Models and terminology

Mon, 17 Jun 2013 15:02:59 -0500

IEC 62264-1:2013 describes the manufacturing operations management domain (Level 3) and its activities, and the interface content and associated transactions within Level 3 and between Level 3 and Level 4. This description enables integration between the manufacturing operations and control domain (Levels 3, 2, 1) and the enterprise domain (Level 4). Its goals are to increase uniformity and consistency of interface terminology and reduce the risk, cost, and errors associated with implementing these interfaces. IEC 62264-1 can be used to reduce the effort associated with implementing new product offerings. This second edition cancels and replaces the first edition published in 2003. It constitutes a technical revision and includes the following significant technical changes with respect to the previous edition:
- the functional hierarchy in 5.2 was extended using the definitions from IEC 62264-3;
- the equipment hierarchy in 5.3 was extended using the definitions from IEC 62264-3;
- a physical asset equipment model was added in 5.3;
- the generic model of manufacturing operations management categories in Clause 7 was added using information from IEC 62264-3;
- the formal UML models that were in Clause 7 were moved to IEC 62264-2 and the remaining data definitions are now in Clause 8;
- the capacity and capability model in Clause 8 was extended;
- new Annexes A and B were moved from IEC 62264-3;
- Subclause 5.5 on the decision hierarchy was removed and a reference added to ISO 15704;
- Annex C, D, E were moved to a Technical Report;
- Annex F was removed.

IEC 62246-1-1 Ed. 1.0 b:2013 : Reed switches - Part 1-1: Generic specification - Quality assessment

Mon, 17 Jun 2013 15:02:59 -0500

IEC 62246-1-1:2013 is a quality assessment specification which defines requirements and tests to reed switches for use in general and industrial applications. This standard selects from IEC 62246-1:2011 and from other sources the appropriate test procedures to be used in detail specifications derived from this specification. This standard describes sampling and test schedules for qualification approval procedures, quality conformance inspection, formation of inspection lots and intervals between tests. This first edition cancels and replaces the first edition of IEC/PAS 62246-2-1 published in 2008. It is a technical revision. This edition includes the following significant technical changes with respect to the previous editions:
a) inclusion of introduction;
b) update of references, terms and definitions;
c) renumbering of clauses to bring them into a more logical order;
d) inclusion of the generic specifications for reed switches;
e) update of typical applications.

This publication is to be read in conjunction withIEC 62246-1:2011.

IEC 62127-3 Ed. 1.1 b:2013 : Ultrasonics - Hydrophones - Part 3: Properties of hydrophones for ultrasonic fields up to 40 MHz CONSOLIDATED EDITION

Mon, 17 Jun 2013 15:02:59 -0500

IEC 62127-3:2007+A1:2013 specifies relevant hydrophone characteristics. This standard is applicable to hydrophones employing piezoelectric sensor elements, designed to measure the pulsed and continuous wave ultrasonic fields generated by ultrasonic equipment; hydrophones used for measurements made in water; and hydrophones with or without an associated pre-amplifier. IEC 62127-1, IEC 62127-2 and IEC 62127-3 are being published simultaneously. Together these cancel and replace IEC 60866:1987, IEC 61101:1991, IEC 61102:1991, IEC 61220:1993 and IEC 62092:2001. The French version of this standard has not been voted upon. This consolidated version consists of the first edition (2007) and its amendment 1 (2013). Therefore, no need to order amendment in addition to this publication.

IEC 62127-3 Amd.1 Ed. 1.0 b:2013 : Amendment 1 - Ultrasonics - Hydrophones - Part 3: Properties of hydrophones for ultrasonic fields up to 40 MHz

Mon, 17 Jun 2013 15:02:59 -0500

IEC 62056-8-3 Ed. 1.0 b:2013 : Electricity metering data exchange - The DLMS/COSEM suite - Part 8-3: Communication profile for PLC S-FSK neighbourhood networks

Mon, 17 Jun 2013 15:02:59 -0500

IEC 62056-8-3:2013 specifies the DLMS/COSEM PLC S-SFK communication profile for neighbourhood networks. It uses standards established by IEC TC 57 in the IEC 61334 series.

IEC 62056-7-6 Ed. 1.0 b:2013 : Electricity metering data exchange - The DLMS/COSEM suite - Part 7-6: The 3-layer, connection-oriented HDLC based communication profile

Mon, 17 Jun 2013 15:02:59 -0500

IEC 62056-7-6:2013 specifies the DLMS/COSEM 3-layer, connection-oriented HDLC based communication profile.

IEC 62056-6-2 Ed. 1.0 b:2013 : Electricity metering data exchange - The DLMS/COSEM suite - Part 6-2: COSEM interface classes

Mon, 17 Jun 2013 15:02:59 -0500

IEC 62056-6-2:2013 specifies a model of a meter as it is seen through its communication interface(s). Generic building blocks are defined using object-oriented methods, in the form of interface classes to model meters from simple up to very complex functionality.

IEC 62056-6-1 Ed. 1.0 b:2013 : Electricity metering data exchange - The DLMS/COSEM suite - Part 6-1: Object Identification System (OBIS)

Mon, 17 Jun 2013 15:02:59 -0500

IEC 62056-6-1:2013 specifies the overall structure of the OBject Identification System (OBIS) and the mapping of all commonly used data items in metering equipment to their identification codes. OBIS provides a unique identifier for all data within the metering equipment, including not only measurement values, but also abstract values used for configuration or obtaining information about the behaviour of the metering equipment.